installation and maintenance instructions carefully!
1)Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to different loads, extra functions,
sensor settings (only with sensor programmes), water supply temperatures, water hardness and power supply voltage.
2)Energy label programme in compliance with EN 50242. - Information for Test Laboratories:
for more detailed information on the EN comparison test and
other tests, contact the following address: “nk_customer@whirlpool.com”.
3)The antibacterial action has been shown in collaboration with the Pasteur Institute, Lille (France), in conformity with. Standard NF EN 13697 - November 2001.
1. OVERVIEW
Programme selector
START button
The indicator lights up during operation, flashes when a fault
occurs, and goes off at the end of the programme.
START button RESET function:
Press this button for at least 2 seconds; the selected programme
and options are cancelled. Main failure displays (repeated flashing
of the START indicator lamp) can be cancelled by RESETTING.
Detailed instructions are given in chapter 5 “What to do, in the
event of...”.
Rinse aid level indicator and salt level indicator
They light up when rinse aid or salt need to be added.
Add just before starting a wash cycle.
Fault indication and wash time display
In normal operation it indicates the remaining time (h:mm),
whereas with “Delayed start” selected it indicates the time
remaining until programme start (hh).
If “F..” appears on the display, see chapter 5 “What to do, in the
event of.
“Delayed start” button
Press the button (repeatedly) to delay the start of the programme.
Adjustable from 1 to 24 hours. With each press of the button, the
delayed start indicator increases by one hour and after 24 restarts
from 00. Then press the START button. The dishwasher will start
after the set time.
Detergent setting upon initial use and when using a different type of detergent
1.Select the third programme in the relative table.
2.Press the START button for approx. 7 sec. to change the display.
3.Using the START button, select the desired detergent:
Display shows: 2 -1 = 2 in 1, 3 -1 = 3 in 1, 4 -1 = other combined action
detergents (in this way, the rinse aid and/or salt indicator is deactivated).
Display shows OFF = Powder detergent (factory setting).
(rinse aid level and salt level indicator activated).
4.Switch the appliance off and then switch it on again. The selected detergent
type will be indicated on the display for approx. 3 seconds .
Half Load/Multizone button
Load the upper or lower rackonly.
Press once = wash upper rack (the indicator/symbol lights up)
Press twice = wash lower rack (the indicator/symbol lights up)
Press 3 times = Off (Half load/Multizone deactivated).
When washing without the upper rack, press the “Half load” (i.e.
“wash lower rack”) button twice (the corresponding indicator/
symbol lights up).
Power Clean
An additional spray level offers better cleaning result and more
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Bauknecht GSIP 40 POWER IN wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.