Bedienungsanleitung Bauknecht wate 9573 3 (Seite 2 von 2) (Englisch)

309228

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 412 10045

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized

conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the

values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the

household conditions applicable at that time.

** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump

drains the water out.

*** Reference programme for Energy label.

1. Close the drum doors and check that they are

properly locked.

2. Add detergents and additives into the dispenser to

no more then the

“MAX”

level mark, as follows:

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

• Chlorine bleach

• Stain remover agents

• Anti-scale agents (if necessary)

3. Turn the

programme selector knob

to the

desired programme.

The remaining time display shows the duration of the

chosen programme (in hours and minutes) and the

indicator light of the

“Start/Pause”

button flashes.

The programme sequence and the predefined

spin speed indication corresponding to the

selected programme lights up.

The preselected temperature can be altered by

pressing the “+” or “-” button.

When you select an option authorized by the

programme, the corresponding indicator lights up,

except if the combination of programme,

additional options and temperature is not possible.

“Easy Ironing” button

• Can be used together with “Cotton”, “Synthetics” and

“Daily Mixed” programmes to make ironing easier.

• Increases the water quantity in rinsing and the

clothes are spun in a softer manner.

“Prewash” button

• Only for heavily soiled loads

(for example sand, granular dirt).

“Intensive Rinse” button

• The amount of water is increased to ensure a

more intensive rinse.

• This option is particularly suitable for areas with

very soft water or washing linen laundry for

people with skin allergies.

“Rinse Hold” button

• The laundry remains in the last rinse water

without progressing to the final spin cycle to

avoid creasing and prevent colours from fading.

• This option is particularly recommended for the

“Synthetics”, “Delicates” and “Daily Mixed”

programmes.

• This function is particularly useful if you want to

postpone spinning to a later time, or if you want

to drain only.

Note:

The programme with “Rinse Hold” stops

when the “Rinse Hold” indicator light flashes on the

“Programme Sequence Indicator”.

CONSUMPTION DATA

Programme

Temperature

Selector

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)*

Cotton / Hygienic+ 95 5.0 49** 1.60 2:05

Cotton *** 60 5.0 48 0.85 2:15

Coloured Cotton 40 5.0 48 0.60 2:00

Synthetics 60 2.0 55** 0.70 1:30

Synthetics 40 2.0 50 0.50 1:15

Daily Mixed 40 3.0 45 0.45 1:00

Delicates 40 1.5 50 0.50 0:45

Rapid 30 3.0 35 0.40 0:30

Wool 40 1.0 55 0.60 0:45

Handwash 30 1.0 40 0.40 0:35

PREPARATION OF WASH CYCLE

SELECT THE DESIRED OPTION

Appliance in “Rinse Hold”:

• Press the “Rinse Hold” button again: the

programme will terminate automatically with the

selected spin cycle.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain /

Reset” programme and press the

“Start/

Pause”

button again.

“Spin Speed Reduction” button

• Every programme has an automatically allocated

maximum spin speed.

• Press the button to set another spin speed.

•

If the spin speed “

” is selected, the final spin is

cancelled, but not the intermediate spins. The

programme ends with a drain cycle.

The “Start Delay” button allows the user to run the

machine at his convenience, for example at night

when electricity is cheaper.

• Select programme, temperature and options.

• Press the “Start Delay” button several times to

select the delay time by 1 to 19 hours;

•Press the

“Start/Pause”

button. The indicator

light of the

“Start/Pause”

button lights up and

the lamp of the “Start Delay” button flashes.

• The time delay indication disappears when the

programme starts and is replaced by the

remaining time.

• The number of hours preselected can be reduced

later by pressing the “Start Delay” button again.

To cancel the “Start Delay” option

• Turn the programme selector to the “ ” position.

• Reselect the desired programme and options

and press the

“Start/Pause”

button.

Turn on the tap and press the

“Start/Pause”

button. The indicator light of the

“Start/Pause”

button lights up. The indicator lamp shows the

sequence reached by the programme. After starting

the programme, the programme sequence indicator

signals the Wash, Rinse and Spin phases.

Note

: If there is a power interruption or if the

appliance is disconnected during the cycle, the

programme will run again from the point where it

was interrupted.

For safety reasons, the lid is locked during certain

phases of the cycle. At the end of the cycle or during

an interruption, the lid unlocks automatically after

about 1 minute.

• The remaining time is on “0: 00” and the “End”

lamp lights up.

1. Turn the programme selector to the “ ”

position.

2. Turn the tap off.

Open the lid and the drum doors and unload the

machine.

1. Select the new programme using the

programme selector. If necessary, select the

additional options and the spin speed. The

luminous indicator of the

“Start/Pause”

button flashes.

Note: the “Start Delay” and “Prewash” options

cannot be selected after a programme change.

Press the

“Start/Pause”

button. The new

programme selected continues at the same

position where the previous programme was

interrupted.

Note:

Do not add detergent for this

programme.

If, for any reason, you wish to interrupt the

programme for a certain time and continue it later:

1. Press the

“Start/Pause”

button. The light

flashes.

2. After the desired pause, press again on the

“Start/Pause”

button.

1. Set the programme selector to “Drain / Reset”.

2. Press the

“Start/Pause”

button to start the

“Drain / Reset” programme.

START DELAY

PROGRAMME START

LID LOCK

END OF WASH CYCLE

CHANGE THE PROGRAMME OR OPTIONS

DURING THE CYCLE

PAUSE/INTERRUPT A PROGRAMME

CANCEL PROGRAMME

Bauknecht wate 9573 3 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info