Bedienungsanleitung Bauknecht wats 5550 (Seite 13 von 17) (Englisch)

306045

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

What should I do when the automatic safety system detects a malfunction?

The programme is interrupted and various indicators (depending on model) point to the source of the

fault.

Fault description table.

a.Water inlet fault (no or

insufficient water supply)

The display alternately shows

“FH”. Switch off the appliance

by turning the programme

selector to the “ ” position

and unplug it.

Check whether:

•

the tap is fully turned on and

the water supply pressure is

sufficient;

•

the water inlet hose is kinked;

•

the mesh filter in the water

inlet hose is blocked (see “Care

and Maintenance”);

•

the water in the water inlet

hose is frozen.

•

the appliance has a safety hose

and the safety valve is open

(red indicator in the safety

valve inspection window).

In this case replace it with a

new safety hose.

Reconnect the appliance.

Reselect the desired

programme and press the

“Start/Pause”

button to

restart the programme.

If the fault re-occurs, contact

the After-Sales (see “After-

Sales Service”).

b.Draining out fault

The display alternately shows

“FP”. Switch the appliance off

by turning the programme

selector to the “ ” position

and unplug it.

Check whether:

•

the drain hose is kinked (see

“Installation”);

•

the pump impeller is

obstructed (see “Cleaning the

Foreign Body Trap”).

•

the water in the drain hose is

frozen.

•

if water has remained in the

drum, you can drain it by

following the instructions in

the chapter “Draining Residual

Water”.

IMPORTANT

: Before draining,

allow the wash water to cool

down.

Reconnect the appliance.

Reselect the desired

programme and press the

“Start/Pause”

button to

restart the programme.

If the fault re-occurs, contact

After-Sales Service (see “After-

Sales Service”).

c. Electrical module fault

The display shows “F4” to

“F15”.

Select a programme and press

the

“Start/Pause”

button

again.

If the fault re-occurs, contact

After-Sales Service (see “After-

Sales Service”).

d.Water Stop fault

(depending on model)

An audible signal sounds and

the pump operates. The light

of the Water Stop indication is

on or the display shows “FA”.

Switch the appliance off by

turning the programme

selector to the “ ” position,

unplug the appliance and turn

off the water tap.

The “Water Stop” fault may

have been triggered by:

1.too much foam.

a leak in the inlet hose or in the

appliance.

Tilt the appliance forwards

carefully to allow the water to

drain out.

Then:

1.reconnect the appliance,

turn on water supply (if

“Start/Pause”

button is not

pressed, but the machine

begins to fill, turn off the

water supply tap and contact

After-Sales Service),

reselect the desired

programme and press the

“Start/Pause”

button.

If the fault occurs again,

contact After-Sales Service

(see “After-Sales Service”).

The pilot lamp goes on. Fault description

“Water tap” “Water inlet fault”

- “Draining fault”

- “Electrical components fault”

“Water Stop” Water Stop fault

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht wats 5550 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht wats 5550

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info