Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer to the
default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Standard Cotton programme and basis for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
*** After programme end and spinning with maximum selectable spin speed, in default programme setting.
Power consumption in off-mode 0.11 W / in left-on mode 0.11 W
CHILD LOCK BUTTONS
You can lock the buttons of the control panel
against improper use (e.g. by children).
•Press both of the child lock buttons
simultaneously and hold them for at least 3
seconds.
•To unlock the buttons again: proceed in the same
way.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for
Use.
“Water tap closed” - no or not sufficient inlet
water.
“
Service” - failure or malfunction of an electrical
component.
“Clean pump” - waste water is not pumped out.
Spin speed on display blinks: unbalance during
spinning
•
PROGRAMME END
The “Lid open” indicator lights up, and the
display shows “End”. After about a quarter of
an hour, the washing machine will switch off
completely to save energy.
1. Turn the programme selector to the “O”
position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the
interior of the machine to dry.
1.
CHANGE PROGRAMME AND/OR OPTIONS AF-
TER PROGRAMME START
Press the “Start/Pause” button to pause the
programme. The light blinks.
2. Select the new programme, temperature, any
options and another spin speed if you want.
3. Press the “Start/Pause” button again. The
new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL A RUNNING PROGRAMME BEFORE THE END
The “Reset/Drain” button cancels a programme
before the end.
•Press the “Reset/Drain” button for at least 3
seconds. The water is drained out; it may last a
while until you can open the lid.
“Fresh Finish” button
•Select this option if you cannot unload the
laundry soon after programme end, or if you
tend to forget the laundry in your washing
machine. It will help to keep your laundry fresh.
•The washing machine will start to tumble the
laundry periodically after programme end.
•The light of the “Fresh Finish” button will blink
while this function is active, and the display will
show an animation.
•The periodic tumbling will last up to
approximately 6 hours after the end of your
wash programme, and you can stop it at any time
by pressing the “Fresh Finish” button. It will last
a while until you can open the door.
•After the “Fresh Finish” period has run out, the
display indicates “End”.
“Prewash” button
•Only for heavily soiled loads (for example
sand, granular dirt). Increases the cycle time by
approximately 15 min.
•Do not use liquid detergent for the main wash
when activating the Prewash option.
“Intensive rinse” button
•More water is added and rinse cycle is
prolonged.
•This option is particularly suitable for areas with
very soft water, washing baby linen and helping
people with allergies.
“Spin” button
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If you select spin speed “0”, the final spinning
is cancelled and the water is drained out only.
However, intermediate spin phases remain
during the rinse.
1.
PREPARATION OF THE WASH CYCLE
Load the washing machine, close the drum door
and check that it is closed properly.
2. Pour in the detergent and any additives, as
described overleaf and in the instruction manual.
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The time display
shows the duration of the chosen programme
(in hours and minutes), and the lamp next to the
“Start/Pause” button flashes. The indication
lamp of the predefined spin speed lights up. If
you do not start the programe soon after having
made your choice, the washing machine will
switch off automatically after about a quarter of
an hour. Switch on the washing machine again by
turning the programe selector back to ”O“ and
then to the desired programe.
SELECT ANY DESIRED OPTION
When the combination of programme and additional
option(s) is not possible, the indication lights switch
off automatically. Unsuitable combinations of
options are deselected automatically.
“Rapid” button
•Enables quicker washing by shortening the
programme duration.
•Recommendable for small loads or only lightly
soiled laundry.
START DELAY
The “Start delay” button allows the user to run the
machine at his c onvenience, for example at night
when electricity is cheaper.
•Do not use liquid detergent when activating this
function.
•Select programme, spin speed and options.
•Press the “Start delay” button several times to
select a delay time by 1 to 24 hours.
•Start the programme (see “Progremme
Start”). The indication lamp over the “Start
delay” button lights up and goes off when the
programme starts.
•Once having pressed the “Start/Pause” button,
the countdown of the time delay begins. The
time delay indication on the display disappears
when the programme starts and is replaced by
the remaining time.
•After the “Start/Pause” button has been
pressed, the number of hours preselected can
be reduced by pressing again the “Start delay”
button.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
•Turn the programme selector to another
position or press the “Reset/Drain” button.
..after having pressed the “Start/Pause”
button:
•Press the “Reset/Drain” button for at least 3
second. The start delay indicator light goes off.
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause”
button lights up.
The display shows the remaining programme time.
Due to variations in load and temperature of inlet
water, the remaining time is newly calculated in
certain programme phases. If this is the case, an
animation appears on the time display.
“LID OPEN” INDICATION
Before starting and after end of a programme,
the lamp lights to show the the lid can be opened.
As long as a wash programme is running, the lid
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel a
running programme before the end”.
Programme
Tempe-
rature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hrs : min)
Approximete remaining moisture
content (%)***
without “Rapid”with “Rapid”1000 rpm1100 rpm1200 rpm
Hallo, die Einstellungen zur Schleuderdrehzahl wir über das Tablo eingestellt von 400 bis 1200 umdrehungen..Auf der rechten Seite des Sablos.Muss allerdings JEDESMAL neu eingestellt werden.
Beantwortet 11-2-202407:06
WMT Eco star 732 Di Fehlermeldung "F08". Obwohl alles funktioniert, Heizung, Temperaturfühler, kein Kabelbruch, zeigt die Maschine nach Programmende immer Fehler "F08" an?
Eingereicht am 18-12-202313:41
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Bauknecht WMT ECOSTAR 732 DI wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Andere Handbücher von Bauknecht WMT ECOSTAR 732 DI
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
