Bedienungsanleitung Danfoss TP9000 Si (Seite 1 von 2) (Englisch)

769351

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

TP9000 Si

User Instructions

A. Setting the correct Time and Day

Fig. 1

B. Accepting the Factory Settings

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Before beginning programming, you should reset the unit. Open the ﬂap on the front

of the clock. Press the RESET button using a non-metallic object (e.g. end of a bic biro

pen top). (Fig 1)

The time and date are factory set and do not need to be set.

The TP9000 comes ready programmed with a set of Hot Water times and Central Heating

times and temperatures to suit the average household. If you wish to alter these settings

follow instructions below.

Your unit is set to operate in 7 day mode.

7 day – diﬀerent settings for each day of the week

Please follow the instructions below:

C. Programming your central heating - 7 day mode

• A)Press the CH/HW button until the CH mode is selected (Fig 2a)

• B) Press PROG to show the 1st pre-set time and temperature (Event 1 Mon) (Fig 2b)

• C) Use + or – buttons to adjust the TIME (press and hold to change in 10 min

increments). (Fig 3)

• D) Use Λ or V buttons to adjust the TEMPERATURE. (Fig 4)

• E) Press NEXT to move to next preset time & temp (Event 2) (Fig 5)

• F) Repeat steps c, d and e for programming Events 3, 4, 5 & 6.

• G) to select the next day, press DAY/HOL and repeat steps c, d, and e (Fig 6)

• H) repeat process as necessary to complete programming for all 7 days

To return to normal operating mode press and hold PROG until screen returns to the current

time. (Fig 7)

(a)

(b)

The TP9000 is a programmable room thermostat with combined hot water time

control.

A programmer allows you to set On and Oﬀ time periods to suit the lifestyle of the

occupier.

A room thermostat works by sensing the air temperature, switching on the heating

when the air temperature falls below the thermostat setting, and switching it oﬀ

once this set temperature has been reached. A programmable room thermostat

lets the occupier choose what times they want the heating to be on and what

temperature it should reach while it is on. It will allow you to select diﬀerent

temperatures in your home at diﬀerent times of the day (and days of the week) to

meet your particular needs.

The TP9000 controller is also unique in that it also controls the hot water timings in

your home.

D. Programming your hot water - 7 day mode

• A)Press the CH/HW button until the HW mode is selected (Fig 8)

• B) Press PROG to show the 1st pre-set time (Event 1 Mon)

• C) Use + or – buttons to adjust the TIME (press and hold to change in 10 min

increments). (Fig 9)

• D) Press NEXT to move to next preset time(Event 2) (Fig 10)

• E) Repeat steps c and d for programming Events 3, 4, 5 & 6.

• F) To select the next day, press DAY/HOL and repeat steps c, d, and e (Fig 11)

• G) Repeat process as necessary to complete programming for all 7 days

To return to normal operating mode press and hold PROG until screen returns to the current time.

(Fig 12)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Danfoss TP9000 Si Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info