Bedienungsanleitung Elro AP5500 - Pro Alarm System (Seite 5 von 8) (Englisch)

708667

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Indicator

PCB Position

PCB Board

Dip Switches

‘TEST MODE – WALK TEST’ is displayed.

Press to activate Walk Test. ‘ Walk Test Waiting…’ is displayed. Press the ‘ARM’ button

on the Remote Control; Alarm Panel will beep and the type of the device and button will be on the

display. Press the other buttons on the Remote, as each button is pressed the Alarm Panel will beep

and show the button being pressed on the display. KEEP THE ALARM PANEL IN THE TEST MODE!

PIR Motion Sensor:

PIR Sensors are designed to detect movement.

Insert the 9 Volt battery. The PIR will warm-up during 2-3 minutes. The LED will flash. When it is ready

the LED stops. First check the house code: SW2; switch 1 – 8 (must be same as Remote Control). You

can divide your detectors over your total home in zones. You can set the alarm zone the PIR detector

will operate on, by switch the dip switches 1, 2 and 3 (of SW3; dipswitch 1-5) in the position according

schedule above. Mark which zone number on the PIR. For walk test mode you put dip 4 of SW3 On.

Don’t forget to put back in Off. Test the PIR in the walk test mode. In normal mode the PIR will only send

a mew signal after being triggered after 2 minutes

The PIR sensor incorporates an anti-false alarm for where the Sensor might be affected by e.g. insects,

air temperature etc. We recommend high sensitivity, but in case of affection of (e.c. insects) , you can

adjust dip 5 of SW3 to Off: low sensitivity detection!

Door/window magnet:

The Magnetic Contact consists of two parts; a Detector and a Magnet. They are designed to be fitted

to doors or windows with the Magnet mounted on the moving/opening part.

Mounting the door/wind magnet:

Decide which doors/windows are to be protected by fitting Magnetic

Contact Detectors, (usually the front and back doors. Additional detectors

may also be fitted where required to other vulnerable doors or windows,

(e.g. garage, patio/conservatory doors etc).Ensure that the position selected

for the Magnetic Contact detector is within effective range of the Control Panel, (refer to

‘Testing the Control Panel & Remote Control’). Remove the battery holder, and mount the

detector using either the adhesive tape or screws. Fit the Magnet to the moving part of the door/window

opposite the Detector. Ensure that the parallel gap between the Magnet and Detector is less than 10mm

and that the arrow on the Magnet is pointing towards and aligned with the mark on the Detector.

Mounting the PIR motion sensor:

Household pets should not be allowed into an area protected by a PIR detector! Do not locate the

detector facing a window facing direct sunlight. PIR Detectors are not suitable for use in

conservatories. Do not locate the detector where it is exposed to ventilators. Do not locate the detector

DIP 1 DIP 2 DIP 3

Zone 1 OFF OFF OFF

Zone 2 OFF OFF ON

Zone 3 OFF ON OFF

Zone 4 OFF ON ON

Zone 5 ON OFF OFF

Zone 6 ON OFF ON

1 2 3

Open the sensor, take out the battery

connector, and place the battery! Check the

house code; same as PIR and Remote Dip 1-

8 from 1-12. Select the Zone you want: setting

Dip 9-11 according the overview at the PIR.

Mark the Zone number on the magnet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AP5500 - Pro Alarm System Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AP5500 - Pro Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info