Bedienungsanleitung Hotpoint-Ariston AQUALTIS AQC9 2F7 (Seite 2 von 54) (Englisch, Französisch, Portugiesisch)

570598

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Where to put your dryer

• Place your dryer at

a distance from gas

ranges, stoves, heaters,

or cooktops because

flames can damage the

appliance. The dryer

should be installed

in an ambient room

temperature of between

20 to 23°C for optimum

performance. But will function if the room is

between 14 and 30°C. If you are going to install the

appliance under a work counter, be sure to leave

a 10 mm space between the top and any other

objects on or above the machine and a 15 mm

space between the sides and lateral furnishings

or walls. This is to ensure proper air circulation.

The appliance must be installed with the rear

surface placed against a wall.

Ventilation

• When the dryer is in use, there has to be adequate ventilation.

Make sure you put your dryer in an environment that is not damp

and has proper air circulation throughout. Airflow around the dryer is

essential to condense the water produced during the washing, the

dryer will not operate efficiently in an enclosed space or cupboard.

! If using the dryer in a small or cold room some

condensation will be experienced.

We do not recommend that the dryer is

installed in a cupboard but the dryer must never

be installed behind a lockable door, a sliding

door or a door with a hinge on the opposite

side to that of the dryer door.

Less than 1m

Fig. A Fig. B

Water Drain

If the machine is positioned close to a drain it is possible to drain the

condensed water directly without using the waterbottle. In which

case it is no longer necessary to empty the water bottle at the end

of each cycle. If the Dryer is positioned above or close to a Washing

Machine the same drainage can be used. Just remove unlink the

tube indicated in figure A and connect it to the drainage. If the

drainage is further away than the length of the tube it is possible to

buy and connect a tube of the same diameter and the necessary

length in order to reach the drainage. To install the new tube just

substitute the existing one as indicated in figure B inserting it in the

same place.

! The drain tube has to be below 1 m from the bottom of the Dryer.

! Once the Dryer has been installed please assure that the drain

tube is not bent or kinked.

Electrical connections

Before plugging the appliance into the socket,

check the following:

• Make sure your hands are dry.

• The socket must have an earth connection.

• The socket must be able to withstand the

machine’s maximum power output as indi-

cated on the rating plate (see Description

of the tumble dryer).

• The power supply voltage must fall within

the values indicated on the data plate (see

Description of the tumble dryer).

• The socket must be compatible with the

dryer’s plug. Should this not be the case,

replace the plug or the socket.

! DO NOT use extension cords.

! The dryer must not be installed outdoors,

even if the space is sheltered. It can be very

dangerous if exposed to rain or storms.

! Once installed, the dryer’s electrical wire and

plug must be within reach.

! The power cord must not be bent or

squashed.

! The power cord is supplied fitted with a

BS1363 plug and with a 13 amp BS1362 fuse.

If it is necessary to fit a replacement fuse, it must

be a 13 Amp ASTA approved to BS1362 type.

WARNING: The plug must not be used without a

fuse cover. If a replacement fuse holder/cover is

required, it must be of the same colour coding or

wording as shown on the base of the plug.

Replacements are available from authorised

dealers.

Changing the plug

The wires in the power cord are coloured in

accordance with the following.

! If the plug being replaced is a non-rewirable

type, then the cut-off plug must be disposed of

safely. DO NOT leave it where it can be inserted

into a socket and create a shock hazard.

! The power cord must be regularly checked.

If the supply cord is damaged, it must be re-

placed by the manufacturer, its service agent

or similarly qualified persons in order to avoid

a hazard. (see Assistance). New or longer

electric cords are supplied by authorised dea-

lers at a supplementary cost.

! The manufacturer denies any responsibility

should any of these rules not be followed.

! If in doubt about any of the above

consult a qualified electrician.

Installation

10 mm

15 mm

Levelling the tumble dryer

The dryer must be installed level for correct

operation.

When you have installed your dryer in its final

location check that it is level first side-to-side,

then front to back. If the dryer is not level,

adjust the two legs up or down until your dryer

is level.

Before you start using our dryer

Once you’ve installed your dryer and before you use it, clean

the inside of the drum to remove any dust that could have

accumulated during transportation.

Warning ! Before you use your dryer ensure that its has

been in a upright position for at least 6 hours.

Moulded plug

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Green and Yellow (Earth)

wire to terminal marked

“E”, symbol x, or coloured

green and yellow.

Blue (Neutral) wire to

terminal marked ”N” or

coloured black.

13A ASTA approved fuse

to BS 1362.

Brown (live) wire to

teminal marked “L” or

coloured red.

Hotpoint-Ariston AQUALTIS AQC9 2F7 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hotpoint-Ariston AQUALTIS AQC9 2F7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info