Bedienungsanleitung Hotpoint-Ariston ET 1400 (Seite 23 von 24) (Englisch, Französisch)

75380

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Your washing machine could fail to work. Before calling for Assistance (see page 24), make sure the problem can't

easily be solved by consulting the following list.

Troubleshooting

Problem

The washing machine won't

start.

The wash cycle won't start.

The washing machine fails to

load water (The wording H2O is

displayed).

The washing machine

continuously loads and unloads

water.

The washing machine does not

drain or spin.

The washing machine vibrates

too much during the spin cycle.

The washing machine leaks.

In the event of an anomaly, an error

code will appear, such as: F-01.

There is too much foam.

Possible causes/Solution:

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly (the word DOOR is displayed).

 The

button has not been pressed.

 The START/CANCEL button has not been pressed.

 The water tap is not turned on.

 A delayed start has been set (using the Delay Start, see page 19).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap is not turned on.

 There is a water shortage.

 The water pressure is insufficient.

 The START/CANCEL button has not been pressed.

 The drain hose is not fitted between 65 and 100 cm from the floor

(see page 15).

 The free end of the hose is underwater (see page 15).

 The wall drainage system doesn't have a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and call for Assistance. If the dwelling is on one of the upper

floors of a building, there may be drain trap problems causing the washing

machine to load and unload water continuously. In order to avoid such an

inconvenience, special anti-drain trap valves are available in shops.

 The programme does not foresee the draining: some programmes

require enabling the draining manually (see page 18).

 The Easy Iron option is enabled: to complete the programme,

press the START/CANCEL button (see page 19).

 The drain hose is bent (see page 15).

 The drain duct is clogged.

 The drum was not unblocked correctly during installation (see page 14).

 The washing machine is not level (see page 14).

 The washing machine is closed in between furniture cabinets and

the wall (see page 14).

 The water inlet hose is not screwed on correctly (see page 14).

 The detergent dispenser is obstructed.

 The drain hose is not secured properly (see page 15).

 Switch off the machine and unplug the appliance; wait for

approximately 1 minute then switch it on again.

If the problem persists, contact Assistance.

 The detergent is not suitable for machine washing (it should bear the

definition "for washing machines" or "hand and machine wash", or the like).

 You used too much detergent.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston ET 1400 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hotpoint-Ariston ET 1400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info