Bedienungsanleitung Ideal HeatSeeker (Seite 1 von 2) (Englisch)

541860

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Getting started

1. Unpack the camera and remove the lens cap.

2. Press the Power switch and allow the camera to calibrate

itself. During this 15-second time period, the screen

may blank out before the thermal image appears.

3. Check the battery icon on the screen and charge unit

if necessary. The charging port is located inside the

camera flap. A full charge takes about 3.5 hours and

provides 6 hours of continuous use with the LED

flashlight on.

4. At this point, the camera should be ready for use with

the following defaults: Units of Measure: °F and Ft.;

Images are focused and aligned at 6’ from camera

lens; Image is blended at 50%; Auto tracking with

dual cursors is On; Voice/Text annotation is On;

Quick Start Guide

HeatSeeker™ Thermal Imager

Door

Screen

Power

Button

Navigation

Keys

F1 F2 F3 F4

™

then press the F2 key, until Visible Off appears. Then,

use the center nav key to toggle the feature On. Then,

use the right/left keys to adjust the image blend.

9. To freeze the image, press the F3 key. If unsatisfied

with the image, press F3 again to release the image

and enter the active measuring mode again. Press F3

to freeze another image.

10. For on-the-job troubleshooting, such as manually

moving the cursor to a specific location on the

camera’s screen to obtain a specific temperature

reading, refer to the full user’s manual saved on the CD.

11. To save the image to the Micro-SD card, press the

Capture button on the top of the camera. Then, record

a voice tag and/or text caption to identify the file when

retrieving it in the software. If these steps are skipped,

the image is still saved but with a generic file name.

12. The camera then returns to live imaging and is ready

to capture a new image.

13. The camera can be turned off by depressing the

power button until the camera shuts down. The

camera stores and uses the last settings upon the

next startup.

The F4 key can be used to enter the menu to change

settings and view saved images onscreen. Refer to the

operating manual to learn the camera’s full capabilities.

Ambient temperature is

set at 72°F; Emissivity is

set for 0.95; Auto Power

Off is set for 20min.

5. To customize the camera

from any of the defaults,

please see the Customizing

the Camera Setup section

further in this guide.

6. Point the camera at the

object of interest, noting that the camera is

focused/aligned at 6’. Ensure your fingers do not

obscure the small visual lens.

7. The dual cursors automatically locate the hottest and

coldest temperatures and displays these temperatures

at the top of the screen along with the Δ temperature.

8. To change the % image blend, hit the right/left

navigation keys. Note that the % refers to the amount

of visual image shown. If these keys are not working,

Capture Button

Thermal Lens

Visual Lens

Laser Button

Quick Start Guide: HeatSeeker™ Thermal Imager www.idealindustries.com

Soft Function Keys

a) 100% Thermal

Only

b) 100% Visible

Only

c) 50% Thermal

& 50% visible

12-3484 HeatSeeker 3-fold R 1/26/09 9:52 AM Page 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ideal HeatSeeker Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ideal HeatSeeker

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info