Bedienungsanleitung Indesit IWTE 51251 (Seite 2 von 84) (Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

489354

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Installation

! Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washing machine to

inform the new owner as to its operation and

features.

! Read these instructions carefully: they contain

vital information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the washing machine.

2. Check whether the washing machine has been

damaged during transport. If this is the case, do

not install it and contact your retailer.

3. Remove the four pro-

tective screws and the

rubber washer with the

respective spacer, si-

tuated on the rear of the

appliance (see figure).

4. Seal the gaps using the

plastic plugs provided.

5. Keep all the parts: you

will need them again if

the washing machine

needs to be moved to

another location.

Warning: should the

screws be re-used,

make sure you fasten

the shorter ones at the top.

! Packaging materials are not children’s toys.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furniture

cabinets or other.

2. If the floor is not per-

fectly level, compensate

for any unevenness by

tightening or loosening

the adjustable front feet

(see figure); the angle

of inclination, measu-

red according to the

worktop, must not ex-

ceed 2°.

Levelling your appliance

correctly will provide it with stability and avoid any

vibrations, noise and shifting during operation.

If it is placed on a fitted or loose carpet, adjust

the feet in such a way as to allow enough room

for ventilation beneath the washing machine.

Putting your appliance in place and

moving it.

I f y o u r w a s h i n g

machine is equipped

with a special set of

retractable wheels

you can easy move it.

To lower the wheels

and thus move the

appliance effortlessly,

just pull the lever,

situated on the left-

hand side beneath the base. Once the appliance

is in the required position, put the lever back in

place. The washing machine is now firmly in

place (see figure).

Electric and water connections

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to

a cold water tab using

a ¾ gas threaded con-

nection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other

end of the water inlet

hose to the washing

machine,

screwing it onto the ap-

pliance’s cold water in-

let, situated on the top

right-hand side on the

rear of the appliance

(see figure).

3. Make sure there are no kinks or bends in the

hose.

! The water pressure at the tap must be within

the values indicated in the Technical details

table (on the next page).

! If the water inlet hose is not long enough,

contact a specialist store or an authorised

serviceman.

! Never use hoses that have already been used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit IWTE 51251 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info