T
Clock with Dual
Model: BARM699A
USER MANUAL
INTRODUCTION
Thank
TM
T
Control AM/FM Atomic Weather Clock with Dual
Alarm (BARM699A). The main unit can support up
to 3 sensors. T
contact your local retailer
NOTE Please keep this manual handy as you use
your new product. It contains practical step-by-step
instructions, as well as technical specifications and
warnings you should know about.
OVERVIEW
F
1. SLEEP : Activate
timer
2. RADIO ON / OFF : T
3. ST:
save a channel
4. VOLUME / : Increase / decrease volume
5. CLOCK : Change setting / display
6. AM / FM : T
7. TUNING / SET / : Increase / decrease
setting;
change radio frequency
B
1. MEMOR: View current, maximum and minimum
temperature
2. CHANNEL : Switch remote sensor display
3. Adapter socket
4. ALARM : View alarm status; set alarm
5. °C / °F : Select temperature unit °C / °F
6. RESET : Reset unit to default settings
L
1. Ice warning
1
8
7
9
10
13
14
15
16
17
18
20
19
1
12
2
3
4
5
6
2. Weather forecast
3. Preset radio station number
4. AM
volume level
5. Radio-controlled clock reception icon
6. 12-hour clock
7. Indoor temperature display icon
8. Channel number and sensor reception status
9. Sensor low battery warning
10.
1
12.
13.
14.
15.
16.
17.
18.
19.
20.
R
1. LED status indicator:
Blinks red during data
transmission
2. Ventilation duct
1. Wall mount
2. Battery compartment
3. Battery door
4. T
5. CHANNEL switch
GETTING ST
P
Plug adapter into main unit.
NOTE This product may malfunction when radio
interference appears
revert to normal operation when interference stops.
NOTE Install the
main unit. Press
RESET after each battery change.
not use rechargeable batteries.
you use batteries with product for
performance.
shows when battery is low
UNIT LOCA
Main Indoor temperature area
Remote Outdoor temperature area
REMOTE SENSOR
The
40 seconds and sends them to the main unit.
unit can collect data from up to 3 sensors.
T
:
1. Slide open the battery door
2. Insert the battery
3. Select a channel. Make sure you use a different
channel for each sensor
4. Close the battery compartment.
5. Secure the
wall mount or table stand.
For best results:
•
Place the sensor out of direct sunlight and
moisture.
•
Do
feet) from the main (indoor) unit.
•
Position
unit, as walls,
and furniture.
•
Place with view
the sky
•
Position
winter months as below-freezing temperatures may
affect battery performance and signal transmission.
The
factors. Y may need to experiment with various
locations to get the best results.
Standard Alkaline batteries contain significant
amounts of water of this they will freeze
in low temperatures of approximately -12°C (10°F).
Disposable Lithium batteries have a much lower
threshold for temperature with an estimated freezing
range of below -30°C (-22°F).
Wireless ranges
such as extremely cold temperatures. Extreme cold
may
sensor station. the
fails due
functioning as the temperature rises to within the
normal
will occur to the unit due to low temperatures).
S
The reception shown the outdoor
area shows the status.
ICON DESCRIPTION
Main unit is searching for
the sensor(s)
A
and signal is being
received
and “- -“ The sensor
(Outdoor temperature Search for the sensor or
area) check the battery
T
:
Simultaneously press and
MEM and CHANNEL
for 2 seconds.
NOTE The sensor LED flashes when data is being
sent to the main unit. If the sensor signal is still not
found, check
location.
LIGHT TOUCH KEY
The touch keys used in product have a key lock
function that prevents accidental changes to user
settings. the keys not used
the last minute, key lock function is
activated. key disable key
function and then operate the clock as usual.
CLOCK RECEPTION
This product is designed to synchronize its date and
time automatically
60 signal from the atomic clock in Boulder
The sensor collects the radio signals whenever it is
within 3219 km (2000 miles) of a signal.
NOTE reception minutes first
up or when
RESET is pressed. Once complete, the
reception icon
can take up to 24 hours to get a valid signal.
R
STRONG NO SIGNAL
T:
Press and hold TUNING / SET for 2 seconds.
T
:
Press and hold TUNING / SET for 2 seconds.
flashes when it is searching for the atomic clock
signal and disappears when it is disabled.
CLOCK
T manually the clock sure clock
reception is disabled.
T
:
1. Press and hold
CLOCK for 2 seconds.
2. Press TUNING / SET
/ to change the
settings.
3. Press
CLOCK to confirm.
4. The setting sequence is: US time zone, 12 / 24
hour format, hour
month, day
NOTE The US time zone options are Pacific (P
Mountain (MO), Central (CE) and Eastern (EA).
NOTE The language options are (E) English, (F)
French, (D) German, (I) Italian, and (S) Spanish.
T
:
Press CLOCK to toggle between:
•
Clock with seconds
•
Clock with weekday
•
Calendar
ALARM
T:
1. Press
ALARM to view the alarm. will show on
the display
2. Press and hold
ALARM for 2 seconds.
3. Press TUNING
/ to
minute,
alarm, AM and ST select
band and station respectively
4. Press
ALARM to confirm.
T
:
Press ALARM when in the alarm or
appears when the alarm is set.
T
:
•
Press SNOOZE to silence it for 8 minutes.
OR
•
Press any SNOOZE
and activate it again after 24 hours.
NOTE or flashes when snooze is activated.
WEA
This product
hours within
75 percent accuracy
SUNNY P
TEMPERA
T:
Press °C / °F on the bottom of the unit.
T
:
Press CHANNEL .
•
shows which remote sensor data you are
viewing.
•
is permanently displayed in the indoor
temperature area.
T
:
Press CHANNEL
data is displayed for 3 seconds.
T
:
Press CHANNEL or MEMOR.
T
records for the selected sensor:
Press MEMOR repeatedly
T
:
Select the channel
hold MEMOR for 2 seconds.
BARM699A_EN_R5.indd 1 2/17/06 2:04:50 PM
