Bedienungsanleitung Philips 28DW6734 (Seite 29 von 32) (Englisch)

51045

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Poor reception (in analogue mode)

The proximity of high buildings may be

responsible for ghost pictures, echoing or

shadows.In this case, try manually adjusting

your picture:see "fine tuning" (p.6) or change

the orientation of the outside aerial. In the

event of difficult reception (snowy picture)

switch the NOISE.REDUCT on the FEATURES

menu to ON. (p.7).

Bad picture (in digital mode)

If the picture freezes a lot,or in cases of block

effect, there is a problem of poor reception.

Please check with the signal strenght menu

(see p.8).

Depending on the strength of digital terre s t r i a l

signals available in your are a ,s t a n d a rd aerials used

for analogue transmissions will in most cases

p rovide satisfactory reception of digital signals.I n

g e n e r a l ,set top and communal aerials will not

g i ve satisfactory re s u l t s ,best performance and

stability of digital signals can be achieved if a high-

quality aerial and wiring is installed.

If reception problems are experienced with a

s t a n d a r d aerial,a good quality,n a rrow beam

antenna should be pro fe s s i o n a l ly installed outside

the pro p e rty and aligned to cap t u r e the maximu m

digital signal stre n g t h .Loft antenna's can be used

w h e re an outside installation is not possible,

h oweve r,c a re should be taken to mount the loft

antenna as high as possible and as far aw ay fro m

house wiring as possible.Aerial amplifiers should

o n l y be used when absolutely necessary. D o u b l e

s c r een coaxial cable should be installed betwe e n

the aerial and television re c e i ver and positioned to

avoid close proximity to house wiring.T h e

t e l e vision re c e i ver should be connected dire c t ly to

the coaxial cable,rather than routing the signal

first through other pro d u c t s .

No picture

H ave you connected the aerial socket pro p e r ly ?

H ave you chosen the right system? (p.6)

Is the

contrast or the brightness badly adjusted?

Press È to select one of the smart control

presets.

Po o r ly connected euroconnector cables or aerial

s o c k ets are often the cause of picture or sound

p roblems (sometimes the connectors can

become half disconnected if the TV set is move d

or turned).Check all connections.

Picture adjustment

If the picture is not adjusted properly or if you

have trouble obtaining a clear picture,select

one of the smart control presets È (p.8) and

store using the STORE PP ALL function in the

FEATURES menu.

The picture is too blue or too red! Adjust the

TINT (p. 12).

In the event of difficult reception (snowy

picture) switch the NOISE.REDUCT on the

PICTURE menu to ON. (p.12).

Peripheral equipment gives a black and

white picture

You have not selected the right socket with the

X key: E2 instead of E2 Y/C.

To play a video cassette, check that it has been

recorded under the same standard (PAL,

SECAM, NTSC) which can be re p l ayed by the

video re c o rd e r.

No sound (in analogue mode)

If on certain channels you re c e i ve a picture but no

s o u n d ,this means that you do not have the corre c t

TV system. Modify the SYSTEM setting (p. 6 ) .

The left and right loudspeakers on the TV set do

not work? Check that the external loudspeake r s

switch has not been activated by mistake (p. 2 0 ) .

The Surround Sound loudspeakers do not wo r k ?

For them to function corre c t ly it is essential that

both loudspeakers are connected:c h e c k

c o n n e c t i o n s .

If in doubt, use the SOUND LEVEL menu (p.13)

to check each channel.

Remote control

The TV set does not react to the remote

control;the indicator on the set no longer

flashes when you use the remote control?

Replace the batteries.

Press the TV key to be sure your remote

control is in the TV mode

Standby

When you switch the TV set on it remains in

s t a n d by and the indication LOCKED is displaye d

when you use the keys on the TV set? The

CHILD LOCK function is switched on (p.7).

If the set receives no signal for 15 mins, it

automatically goes into standby mode.

The set consumes energy when it is switched

on.To save electricity, we recommend that you

switch the TV set off using the ON/OFF key.

Still no results?

If your TV set breaks down, never attempt to

repair it yourself: contact your dealer's after-

sales service.

Tips

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 28DW6734 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info