Bedienungsanleitung SeaLife Sea Dragon 5000 - SL676 (Seite 1 von 2) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

776908

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5000

QUICK Guide

Carry

Case

1” ball joint

adapter with

w/ hex key

SEALIFE (C/O PIONEER RESEARCH),

97 FOSTER ROAD, MOORESTOWN, NJ 08057 USA

INFO@SEALIFE-CAMERAS.COM WWW.SEALIFE-CAMERAS.COM

START

Charge the battery.

Place battery in charging

tray. The charging status

indicator is located on

AC power adapter and

will turn green when fully

charged. Note: Battery is

pre-installed in the light.

Remove yellow contact

cover, which prevents

accidental power on.

What’s in the box:

Sea Dragon 5000

light head with YS

adapter attached

Sea Dragon

Overview: The Sea Dragon Pro Photo/Video light delivers 5000 true lumens in a smooth, even 120° wide beam

without hotspots. Unmatched 96 CRI (color rendering index) and 97 TLCI (Television Lighting Consistency

Index) COB LED array that mimics natural sunlight. Two integrated red LED’s “stealth mode” emits an 88°

wide beam that won’t scare away nighttime sea creatures and preserves your eye’s natural night vision.

Brightness is adjusted manually in 4 steps (100% 75%, 50% and 25%) or automatically (from 10% to 100%)

with its built-in photocell light sensor. The flash-detect feature turns off the light for 1 sec. when nearby flash

is fired. The light easily mounts to YS, 1” ball joint or Flex-Connect system of arms, grips, trays and mounts.

The 50Wh battery delivers 50 minute run time at full power and 4hrs at 25% brightness.

Flex-Connect

YS adapter

2Check if O-rings are lubed. The

O-ring is pre-lubed by the factory.

Before each dive, check to make

sure O-ring appears shiny. If not,

apply small amount of silicon lube

to outer surface of O-rings. Wipe off

excess lube.

50W Li-ion battery with

protective cover, charg-

ing tray and AC power

adapter

Int’l plug adapters

for EU, UK and AU

Spare O-rings w/ lube

and emoval tool

3Insert battery in light and screw

on waterproof battery cap until

fully sealed. 4

4Connect light to arm or grip. Use Flex-Connect YS adapter if

connecting light to Flex-Connect system of arms, grips and trays.

Light may also be mounted directly to YS arms and grips. For

mounting to ball joint arms/grips, replace the YS mount with Ball

Joint Mount using the included hex key.

Push and hold power

button for 1 second to

power light on and 2

seconds to power off.

Push and release the power button to cycle through 6

different brightness modes:

100% g 75% g 50% g 25% g Auto g Red g 100%

6The battery status indicator is located around the power button. It

is green when battery charge is 100 - 51%, yellow for 50 - 21%, red

for 20 - 5% and blinking red when less than 5% charge remains.

To activate emergency signal

mode, push and hold power

button for 4 seconds from power

off state. Push and release power

button to select between 1 sec

blink interval and SOS Morse code.

The Auto Flash Detect (AFD) feature is already activated. The light will

power off for 1 second when nearby flash is fired. To deactivate AFD, push

and hold power button for 5 seconds from power off state until status

indicator lights blink. Push and release power button to select between

AFD off (1 blink per sec.) and AFD on (2 blinks). Push and hold the power

button for 2 seconds to save the setting and power off the light.

IMPORTANT:

1. Avoid using the light above water for more than a few minutes. The front of the light head becomes very hot within a few minutes,

which may cause burning if touched. Water is needed to keep the light cool. A thermal sensor will dim the light if it overheats.

2. After use, soak sealed light in fresh water for 20 minutes to dissolve salt residue. Towel dry. Allow light to fully dry before storage.

3. If water has entered the battery compartment or under the lens port, immediately power off the light. On land, remove the battery.

Allow battery compartment to fully dry. Contact your local SeaLife dealer or SeaLife service center in your country for repair service.

4. Do not use battery that has become wet or if outer casing is cracked or damaged. Dispose of wet or damaged battery in accordance

with your local battery recycling regulations.

5. Remove battery from light before transporting, traveling or long term storage. Always use the included protective battery cover when

battery is not inside the light or charging tray to prevent accidental short-circuiting the battery contacts.

6. Do not obstruct the safety pressure release valve located under the light head.

7. Observe all SCUBA dive safety rules and control your buoyancy at all times. Consult your dive instructor for dive safety questions.

8. Visit SeaLife-Cameras.com website for troubleshooting advice, updates to these instructions, spare parts and other helpful information.

GUARANTEE: SeaLife warrants the original

purchaser of this product, for a period of one (1)

year from the date of purchase, that the product is

free from defects in workmanship and materials.

In the event the original purchaser believes there

is a defect in a product, it is recommended that

the purchaser first visit www.sealife-cameras.

com for product updates and information on

how to get warranty repair service. Please contact

your local SeaLife dealer or the importer in the

country where the product was purchased for

return information.

APRIL 2019

Sea Dragon 5000

Pro Photo/ Video Light

(Item SL676)

SeaLife Sea Dragon 5000 - SL676 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info