Bedienungsanleitung Vivanco ur 14 (Seite 3 von 43) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

122732

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

UR 14 UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, Helpline: +49 (0) 4102 231135

entered remains stored. The search stops after

approx. 30 seconds of inactivity.

Automatic code search

Your remote control finds the correct settings

almost automatically in seconds:

1. Switch on the appliance to be

controlled. A channel number, for example,

appears in the display of your satellite receiver.

2. To start the code search, press the

required appliance button, e.g. TV1*) briefly.

3. Then press SET for about 5

seconds until the lamp (LED) starts to blink.

4. Then point the remote control at the

appliance to be controlled while the remote

control emits a different ON/OFF signal every

second.

5. When your appliance reacts, press

SET within 1-2 seconds, to end the search. – If

you ended the search too late, continue to

search using the Manual Code Search (see

above).

6. Finally, test the control code setting

by trying to control, for example, your DVD

appliance. If it does not work correctly, please

try the code search again. The code search

then begins with the next code in the

sequence. - Remember to switch your

appliance, e.g. DVD, back on again if you wish

to continue searching.

Code identification

You can read off the 3-digit codes you have set

at any time:

1. Press the appliance button of the

appliance which code you want to read off, e.g.

TV1.

2. Press the SET button and 1,2,3,

depending on the part of the code you want to

read off. For example, if you press SET+1 after

TV and the code 176 (in this example) has

been set, the lamp blinks once after SET+1 is

released to show that the hundred figure is 1.

All you have to do is count. The ten figure is

indicated after SET+2 is released, e.g. it blinks

7 times for the 7 in 176. The one figure is

indicated after SET+3 is released, e.g. it blinks

6 times for the 6 in 176.

Learning, Programming, of Missing Control

Functions

The LEARN function is used to supplement the

preprogrammed codes. The standard code

may provide most of functions needed, but you

may miss some key functions. Or you didn´t

find any functioning preprogrammed code for a

device. You can capture upto 65 key function

codes, max 40 per device. The last captured

function will overwrite the previous. learnt.

1 For learning of key codes you must use a

functioning orginal remote controller. Please

use fresh batteries for both remote controls.

2 Please point the original´s remote control

transmitter LED towards the receiver LED of

UR 14 (placed on top, same as transmitter

LED). Distance of LEDs between both remotes

shall be approximately 10mm and must be in

straight line of sight. – Sometimes you have to

move the remotes a bit too and fro while

learning, in order to find right positions.

3 Press the LEARN key for about 3

seconds until the LED (lamp) turns on.

4 Within 10 seconds press a device key

(e.g. DVD1)**) briefly. The LED is flashing one

time .

5 Press and release the target key on the

UR 14, that you want to learn (to reprogram)

(e.g. POWER), the LED starts flashing.

6 Press and hold the source key on the

original remote control (e.g. POWER) until the

LED on your UR 14 remote control stops

flashing and changes to on again. That

indicates that a new function code, e.g.

POWER, has been learnt.

7 Repeat steps 4 to 6 to for capturing more

key functions. - If there is a learning(capturing)

problem, the LED blinks 2 times, lights up for

10 seconds. Then repeat steps 4 to 6 for

capturing more keys functions.

8 Press and release LEARN key for exit of

learning mode. – The controller will exit the

learning mode automatically after about 30

seconds of inactivity.

**) Learning is possible for items, which can be

controlled by using device buttons TV1, TV3,

CD, CBL only!

Memory full indication: if the memory is full,

the LED blinks 2 times and then a programmed

key can be overitten or the controller will exit

learnning mode after 10 seconds of idleness.

Reset/deletion of a captured key function

1 Press the LEARN key for about 3

seconds until the LED (lamp) turns on.

2 Press and hold the device button, e.g.

DVD1, which belongs to the to be deleted key

function. The LED will flash once.

3 Press the key of which the captured

function shall be deleted, e.g. 3, additionally

briefly. The LED will flash once and the learnt

code is deleted.

4 Press and release LEARN key for exit of

deletion mode.

Reset/deletion of all captured key functions

for a device:

1 Press the LEARN key for about 3

seconds until the LED (lamp) turns on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vivanco ur 14 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info