Bedienungsanleitung Whirlpool awa 1055 (Seite 2 von 2) (Englisch)

314340

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 100 12605

Prewash cycle increases programme duration by 5 to 15 min. Consumption values were measured in normalized

conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values

in the table in relation to the water supply pressure and temperature, the load and the type of wash.

ADDING DETERGENT AND ADDITIVES

Add the detergent and the additives into the chamber as follows:

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

• Chlorine bleach

• Stain remover agents

• Anti-scale agents (water hardness 4)

Important:

• Be careful not to fill more than the

“MAX”

level mark.

• For programme with pre-wash: do not use liquid detergents.

• For programmes without prewash from cold to 40° C it is recommended to use a liquid detergent

to avoid whitish residues on the coloured laundry.

CLOSE THE DOOR AND SELECT THE PROGRAMME

1. Turn the

programme selector knob

to the desired programme.

2. The remaining time indication lights up and the “Start” button is flashing.

3. Turn the

temperature knob

to the required temperature.

4. Turn the

spin speed selector

to the required setting.

PRESS ANY DESIRED OPTION BUTTON(S). The pilot lamp lights up.

“Intensive Rinse” button

• For improved rinsing efficiency the rinse water level and the cycle time are increased.

• This option is particularly suitable for areas with very soft water washing baby linen and helps

people with allergies.

“Rinse Hold” button

• The laundry remains in the last rinse water without progressing to the spin cycle to avoid creasing

and prevent colours from changing.

• This option is particularly recommended for the programme “Synthetics” or “Delicate”.

• This function is particularly useful if you want to postpone spinning to a later time.

Note: The programme is stopped in “Rinse Hold” at the time the “Rinse Hold” button flashes.

Terminate the “Rinse Hold” option:

• Press the “Rinse Hold” button again; the programme will terminate automatically with the spin

cycle for the present wash programme.

• If you do not wish to spin the clothes, turn the programme selector knob to the drain programme

and push the “Start” button.

“Prewash” button

• Only for heavily soiled loads (for example sand, granular dirt) sensible.

• The cycle time increases from 5 to 15 min.

START DELAY BUTTON

• Select the programme and the option (if necessary). The remaining time indication lights up;

• Press the “Start Delay” button to select the delay time by 2, 4, 6, 8 hours;

• Press the “Start” button. The “Start Delay” light flashes until the programme starts.

• The number of hours preselected can later be reduced pressing again the “Start Delay” button.

To cancel the “Start Delay”.

• Turn the programme selector to the “ ” position.

PROGRAMME START

Open the tap and press the “Start” button. The pilot lamp lights up.

DOOR LOCK

During the running programme the door can be opened for adding further laundry.

The door locks automatically in all rinsing and spinning cycles. If the programme is stopped or the

electrical power supply is terminated, the door lock will open after approximately 1 minute.

Note:

If you open the door during the programme, the “Start” button is flashing. Press it again to

continue the cycle.

PROGRAMME END

• The rest time display is on “End”.

1. Turn the programme selector to the

“ ”

position.

2. Turn the water supply tap off.

3. Open the door and the drum flaps and unload the machine.

CHANGE THE PROGRAMME AND OPTIONS AFTER PROGRAMME START

1. Press the “Start” button to pause the programme. The light flashes.

2. Select the new programme, temperature, spin speed or options.

3. Press the “Start” button to start the programme again.

TO CANCEL A PROGRAMME BEFORE THE END

1. Press the “Start” button to pause the programme. The light flashes.

2. Set the programme selector to “Drain”.

3. Press the “Start” button to start the drain programme.

The door is unlocked as soon as the rest time display is on “End”.

AUTOMATIC SAFETY FUNCTIONS / FAULTS

This washing machine is equipped with automatic safety functions which detect and diagnose faults at

an early stage and react appropriately. Often, however, the faults detected are small enough to be

solved in a matter of minutes. For example:

• The washing machine will not start.

• The additive products are not being fully washed out of the detergent dispenser.

• The washing machine is unstable during the spin cycle.

• The washing machine does not spin at the end of the programme.

Information about the above problem can be found in the “Troubleshooting Guide”.

What should I do when the automatic safety detects a malfunction?

The programme is interrupted and the fault is indicated as follows:

CONSUMPTION DATA

Programme Temperature

selector (°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Programme

duration (min)

Cotton 90 5.0 49 1.60 120

Coloured Cotton 60 5.0 48 1.15 120

Synthetics 60 2.0 54 0.70 120

Synthetics 40 2.0 50 0.50 80

Chrono 30 min 30 3.0 35 0.40 30

Delicate 40 1.5 50 0.50 45

Wool 40 1.0 50 0.50 45

Silk 30 1.0 35 0.40 35

Indicators flashing Solution

Remaining time indication and water tap

See “No or insufficient water supply”.

Remaining time indication Other faults (see “Troubleshooting Guide”)

Whirlpool awa 1055 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool awa 1055

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info