5019 312 10734
1. Load the machine, close the drum doors and check
that they are properly locked.
2. Add detergent and additives into the dispenser to
no more than the “MAX” level mark, as follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softeners and conditioners
• Stain remover agents
• Anti-scale agents (if necessary)
3. Close the lid.
4. Tprogramme selector to the desired
programme and temperature. The lamp next to the
“Start/Pause” button flashes. The indication lamp
of the predefined spin speed lights up.
CONSUMPTION DA
Prewash cycle increases programme duration by aproximately 20 min. Consumption values were measured in normalized conditions in
compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to
the water supply pressure and temperature, the load and the type of wash.
* T
out.
** Reference Programme for Energy Label.
PREP
“DOOR OPEN” INDICA
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a
wash programme is running, the lid remains locked and
must on no account be forced open. In case you have
an urgent need to open it during a running programme,
refer to “Cancel (Reset) a running programme before
the end”.
RED INDICA
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“T
if the fault persists, contact our After Sales Service.
“
The appliance has no or insufficient water supply
the water tap: if the indications still lights up, refer to the
“T
“Clean pump”
W
drain hose is kinked or the filter must be cleaned: in the
latter case refer to the Instructions for Use (“Removing
the Filter
• Add an appropriate amount of in-wash additive for
stain removal (powder) to the main wash chamber
together with your detergent (only use powder
detergent with this option). Respect the
manufacturer
• Prolo
• Appropriate for use of stain removers and bleaches
on oxygen basis. Chlorine or perborate bleaches
must not be used!
“Intensive rinse” button
• The amount of water is increased to ensure a more
intensive rinse.
• This option is particularly suitable for areas with very
soft water
allergies.
“Rinse hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• This option is particularly recommended for the
“Synthetics”, “Daily load” and “Delicates”
programmes.
• It is useful if you want to postpone spinning to a later
time, or if you want to drain out only
• If you select “Rinse Hold”, do not leave items to
soak for too long.
• As soon as the appliance stops in the rinse hold, the
“Rinse hold” lamp of the sequence indicator lights up
and the lamp next to the “Start/Pause” button
flashes.
T
• Press the “Start/P button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
Whirlpool is a registered trademark of Whirlpool USA.
PROGRAMME ST
Open the tap and press the “Start/Pbutton.
The indication lamp next to the “Start/Pbutton
lights up. The programme sequence indicator shows
the current programme phase, running from left to right
through W
phrase is finised, the corresponding indication goes out.
• Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
PROGRAMME END
• All the lights of the programme sequence indicator
are off, and the “Door open
1. T
position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the
interior of the machine to dry
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME ST
1. Press the “Start/Pbutton to pause the
programme. The light flashes.
2. Select the new programme, any options and another
spin speed if you want.
3. Press the “Start/Pbutton again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the
end. Press the “Rbutton for at least 3 seconds.
Any existing water is drained out before the lid can be
opened.
SELECT THE DESIRED OPTION(S)
Selecting or deselecting an option can be done at
any time during the programme. The option will be
applied as long as the corresponding programme
phase has not been ex
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 20 min.
“Clean+” button
• Choose this option if you use an in-wash additive for
stain removal (powder
will optimize the additive’s efficiency to get better
wash performance and stain removal.
• Selectable for programmes “Cotton
“Synthetics”; choose temperature of 30 or 40°C and
use with maximum load.
ST
The “Start delay
at his convenience, for example at night when electricity
is cheaper
• Select programme, spin speed and options.
• Press the “Start Delay
select a delay time of 1, 3, 6, 9 or 12 hours.
The corresponding indicator lamp lights up.
• Start the programme (see “Progremme Start”).
The indication next to the “Start delay
up and goes off when the programme starts.
• Once having pressed the “Start/Pause” button,
the countdown of the time delay begins. When the
programme starts, the start delay indicator light
goes off and is replaced by the programme sequence
indication.
• After the “Start/Pause” button has been pressed,
the number of hours preselected can be reduced by
pressing again the “Start delay
T
..before you press the “Start/P
• T
or press the “Reset” button.
..after having pressed the “Start/P
• Press the “Reset” button for at least 3 second. The
start delay indicator light goes off.
Programme
T
(°C)
Load
(kg)
W
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
White Cotton 95 5.5 55* 1.70 1:55
Cotton** 60 5.5 49 0.93 2:35
Cotton 40 5.5 53 0.55 2:00
Jeans 40 5.5 73 0.55 2:14
Synthetics 60 3.0 54* 0.90 1:40
Synthetics 40 3.0 48 0.55 1:25
Delicates 40 1.5 51 0.50 0:45
Daily load 40 3.0 43 0.48 1:00
Quick wash 15’ 30 3.0 30 0.15 0:15
W
40 1.0 53 0.50 0:45
Handwash 40 1.0 43 0.50 0:35
SuperEco 60 5.5 49 0.73 4:00
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain
programme and press the “Start/Pause” button.
“
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
the rinse. The water is drained out only
