Bedienungsanleitung Whirlpool AWM 6614 (Seite 2 von 2) (Englisch)

521505

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 06196

Whirlpool is a registered trademark of Whirlpool USA

Add detergent as indicated on the front page and as

described in the chapter “Detergent and Additives”

in your Instructions for Use.

Close the door and turn the programme selector to

the desired programme and temperature. The

indication lamp next to the

“Start/Pause”

button

flashes.

Push the button(s) of any option(s) desired - the

respective indication lights up.

When the combination of programme and

additional option(s) is not possible, the indication

lights switch off automatically. Unsuitable

combinations of options are deselected

automatically.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time

by approximately 15 min.

“Eco” button

• With a modified temperature profile and a

slightly prolonged washing duration, the

optimum combination of excellent washing

result and even lower energy consumption is

achieved.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with

very soft water, washing baby linen and helps

people with allergies.

“Rinse hold” button

• The laundry remains in the last rinse water

without progressing to the final spin cycle to avoid

creasing and prevent colours from changing.

• This option is particularly recommended for the

programmes “Synthetics”, “Daily load” and

“Delicates”.

• It is particularly useful if you want to postpone

spinning to a later time, or if you want to drain

only.

Note:

The programme stops to “Rinse hold” at

the time the “Anticrease” light in the programme

sequence indication is on. The indication lamp

next to the

“Start/Pause”

button flashes.

• If you select “Rinse Hold”, do not leave the

laundry items to soak for too long.

Terminate the “Rinse hold” option:

• Press the

“Start/Pause”

button; the

programme will terminate automatically with the

final spin cycle for the present wash programme.

•If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain”

programme and press the

“Start/Pause”

button.

• Increases the water quantity and the clothes are

spun very gently.

CONSUMPTION DATA

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton/Antibacterial 95 6.0 59

1.80 2:00

Cotton 60 6.0 49 1.14 2:10

Cotton with “Eco”

***

60 6.0 49 1.02 2:20

Cotton 40 5.0 56 0.70 2:00

Synthetics 60 2.5 50

0.80 1:35

Synthetics 40 2.5 46 0.50 1:20

Delicates 30 1.5 60 0.50 0:45

Daily load 40 3.0 41 0.50 1:00

Quick wash 30 3.0 41 0.40 0:30

Wool 40 1.0 60 0.50 0:45

Handwash 40 1.0 45 0.50 0:40

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home

may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions

applicable at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain

during rinse. The water is drained out only.

The “Start Delay” allows to run the machine at the

consumer’s convenience, for example at night when

electricity is cheaper.

• Select programme, temperature and options.

• Press the “Start Delay” button to select the

delay time by 1, 3, 6, 9 or 12 hours.

• Press the

“Start/Pause”

button.

The indication next to the “Start Delay” button

lights up and goes off when the programme

starts.

• Once having pressed the

“Start/Pause”

button,

the countdown of the time delay begins. When

the programme starts, the start delay indicator

light goes off and is replaced by the programme

sequence indication.

• After the

“Start/Pause”

button has been

pressed, the number of hours preselected can

be reduced by pressing again the “Start Delay”

button.

To cancel the “Start Delay”

..before you press the “Start/Pause” button:

• Turn the programme selector to another

position or press the

“Reset”

button.

..after having pressed the “Start/Pause” button:

• Press the “Reset” button for at least 3 seconds -

the start delay indicator light goes out.

Open the tap and press the

“Start/Pause”

button.

The indication lamp next to the

“Start/Pause”

button lights up. The programme sequence indicator

shows the current programme phase, running from

left to right through Wash, Rinse, Spin/Drain.

When the programme phase is finished, the

corresponding indication goes out.

Before starting and after end of a programme, the

lamp lights to show that the door can be opened. As

long as a wash programme is running, the door

remains locked and must on no account be forced

open. In case you have an urgent need to open it

during a running programme, refer to “Cancel

(Reset) a running programme before the end”.

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your Instructions for

Use; if the fault persists, contact our After Sales

Service.

“Water tap closed”

The appliance has no or insufficient water supply.

Open the water tap; if the indication still lights up,

refer to the “Troubleshooting Guide” in the

Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned; in

the latter case refer to the Instructions for Use

(“Removing the Filter”).

• All the lights of the programme sequence

indicator are off, and the “Door open”

indication lights up.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press the

“Start/Pause”

button to pause the

programme. The light flashes.

2. Select the new programme (with temperature),

any options and another spin speed if you want.

3. Press the

“Start/Pause”

button again. The

new programme continues at the same position

where the previous programme was

interrupted. Do not add detergent for this

programme.

The

“Reset”

button cancels a programme before

the end.

• Press the

“Reset”

button for at least

3 seconds. Any existing water is drained out

before the door can be opened.

START DELAY

PROGRAMME START

“DOOR OPEN” INDICATION

RED INDICATIONS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

30106196GB.fm Page 2 Wednesday, June 11, 2008 10:54 AM

Black process 45.0° 100.0 LPI

Whirlpool AWM 6614 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWM 6614

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info