ADD DETERGENTS, CL
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“DOOR OPEN” INDICA
Before starting and after end of a programme, the lamp
lights to show the the door can be opened. As long
as a wash programme is running, the door remains
locked and must on no account be forced open.
In case you have an urgent need to open it during a
running programme, refer to “Cancel (Reset) a running
programme before the end”.
PROGRAMME ST
Open the tap and press the “Start(P” button.
The indication lamp next to the “Start(P” button
lights up. The programme sequence indicator shows the
current programme phase, running from left to right
through W
When the programme phase is finished, the
corresponding indication goes out.
PROGRAMME END
• All the lights of the programme sequence indicator
are off
1. T
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME ST
1. Press the “Start(P” button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the “Start(P” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the
end.
• Press and hold the “R” button for a few
seconds. Any existing water is drained out. It may last
some time until the door can be opened.
The “Start Delay
consumer
electricity is cheaper
when activating “Start delay
•
•
time by 1, 3, 6, 9 or 12 hours.
• “Start(P” button.
The indication over to the “Start Delay
lights up and goes off when the programme
starts.
• “Start(P” button,
the countdown of the time delay begins. When
the programme starts, the start delay indicator
light goes off and is replaced by the programme
sequence indication.
• “Start(P” button has been
pressed, the number of hours preselected can be
reduced by pressing again the “Start Delay
button.
T
..before you press the “Start(P” button:
•
or press the “Reset ” button.
..after having pressed the “Start(P” button:
• R” button for at least 3 seconds -
the start delay indicator light goes out.
ST
Push the button of any option desired - the respective
indication lamp lights up.
If the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically
deselected automatically
“Rapid” button
• Enables quicker washing by shortening the
programme duration.
• Recommendable for small loads or only lightly
soiled laundry
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt). Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash
when activating the “Prewash” option.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with
very soft water
people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water
without pregressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only
• If you select “Rinse hold” do not leave items to
soak for too long.
Note: The programme stops to “Rinse hold” at
the time the “Rinse hold” lights in the preogramme
sequence indication is on. The indication lamp next
to the “Start(Pause) ” button flashes.
T
• Press the “Start(P” button; the programme
will terminate automatically with the final spin
cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain
programme and press the “Start(Pause) ” button.
“Spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
the rinse. The water is drained out only
Whirlpool is a registered trademark of Whirlpool USA.
5019 301 01261
Programme
T
(°C)
Load
(kg)
W
(l)
Energy
(kWh)
without “Rapid”
Approx. programme duration
(hours : minutes)
without “Rapid” with “Rapid”
Cotton 95 5.0 53* 1.70 2:00 -
Cotton **
60 5.0
44 0.75
4:00
2:30
Cotton ** 60 2.5 32 0.65 2:20 ***
Cotton 40 5.0 49 0.60 2:45 1:45
Cotton ** 40
2.5
32 0.55
2:30 ***
Synthetics 60 2.5 50* 0.70 1:30 1:09
Synthetics 40 2.5 45 0.50 1:15 0:54
Delicates
30
1.5 50
0.50
0:45 -
Daily load 40 3.0 45 0.45 1:00 -
Quick wash 30 3.0 40 0.40 0:30 -
W
40 1.0 55 0.60 0:45 -
Handwash 40 1.0 45 0.60 0:40 -
Handwash 30 1.0 45 0.50 0:36 -
CONSUMPTION DA
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the
home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type
of wash.W
speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that
time (see also “T
*
T
** Reference programmes for Energy Label.
*** Automatic adaptation of programme duration after detection of wash load
Add detergents as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
• Tprogramme selector to the desired
programme and temperature.
• The indication lamp next to “Start(P”
button blinks.
• The indication lamp of the predefined spin speed
lights up.
FAIL
In case of any failures or irregularities, consult the
“T
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component.
“
The washing machine has no or insufficient water
supply; the water tap might be closed or the water
inlet hose kinked.
“Clean pump”
W
be kinked or the filter must be cleaned (see “Cleaning
the filter
