5019 301 06101
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
1. Turn the
programme selector
to the desired
programme and temperature.
2. The
time display
shows the duration of the
chosen programme (in hours and minutes), and
the
“Start”
indication lamp flashes.
3. The indication lamp of the predefined
spin
speed
lights up.
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Eco” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
“Prewash” button
• Only for heavily soiled loads (
granular dirt)
by approximately 15 min.
• Do not use liquid detergent for the main wash
when activating the “Prewash” option.
“Cold wash” button
• W
• Suitable for delicate laundry items with wash
temperature recommendation of max. 30°C on
the care label.
• Selectable only on the lowest temperature step
of each programme.
“Easy ironing” button
• Can be used together with “Cotton
“Synthetics” and “Daily load” programmes to
make ironing easier
• Increases the water quantity and the clothes are
spun very gently
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with
very soft water
people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only
• If you select “Rinse hold” do not leave the laundry
items to soak for too long.
Note:
The programme stops to “Rinse hold” at
the time the “Ri
sequence indication is on. The in
next to the
“Start”
button flashes.
CONSUMPTION DATA
Programme
Te m e a u r e
(°C)
Load
(kg)
W
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
Cotton 95 7.0 70
**
2.10 2:10
Cotton with “Eco”
***
60 7.0 60 1.33 2:20
Cotton 40 7.0 65 0.75 2:05
Synthetics 60 3.5 48
**
0.95 1:35
Synthetics 40 3.5 44 0.55 1:20
Delicates 30 2.5 60 0.45 0:50
Daily load 40 5.0 66 0.60 1:00
Quick wash 30 5.0 60 0.30 0:30
W 40 2.0 60 0.65 0:45
Handwash 40 2.0 45 0.65 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type o
*
The remaining time indicator can deviate from the values in the table, because it
applicable at that time.
**
Tut.
***
Reference P
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTIO
T
• P
“Start”
button; the programme will
terminate automatically with the final spin cycle
for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain
and press the
“Start”
button.
“
• Every programme has a predefined spin speed.
• P
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent
when activating the “Start Delay”.
• Select programme, temperature and options.
• P
time by 1 to 23 hours;
• P
“Start”
button.
The indication light over the “Start Delay
button flashes and the countdown of the delay
time begins.
•Ton disappears when the
programme starts and it is replaced by the
remaining programme time.
• Once having pressed the
“Start”
button, the
number of hours preselected can be reduced by
pressing again the “Start Delay
T
..before you press the “Start” button:
• T
position or press the
“Reset”
button.
..after having pressd the “Start” button:
• Press the
“Reset”
button for at least 3 seconds - the
start delay time disappears from the time display
Open the tap and press the
“Start”
button. The
indication lamp next to the
“Start”
button lights up.
The programme sequence indicator shows the current
programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
The time display shows the remaining programme
time. Due to variations in load and temperature of inlet
water, the remaining time is newly calculated in certain
programme phases. If this is the case, an animation
appears on the time display.
Before starting and after end of a programme, the
lamp lights to show that the door can be open
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by
a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
• All the lights of the programme sequence
indicator are off
indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry
1. Press the
“Start”
button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin spee
3. Press the
“Start”
button again. The new
programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
The
“Reset”
button cancels a programme before
the end.
• Press the
“Reset”
button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PRO
“DOOR OPEN” INDICATION
RED INDICA
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30106101GB.fm Page 2 Friday, September 28, 2007 6:40 PM
Black process 45.0° 100.0 LPI
