Bedienungsanleitung 9ZAP 9Z World Champion Model 2 (Seite 27 von 29) (Englisch)

42029

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

ESCRIPTION

UNCTIONS

Idling area

Point 1 is the stick maximum slow area. Therefore, adjust the idling mixture so that a

good idling speed is obtained. If the carburetor is still flooded when point 1 is 0%,

raise throttle curve point 1~2 and increase the air and readjust the throttle trimmer.

Set a value so that points 2 and 3 are connected to the hovering area.

Hovering area

Points 4~6 are the hovering area. Slowly hover and adjust the mixture while observ-

ing the hovering state. After hovering adjustment, land and take off and perform

climb adjustment. Next slowly climb from hovering and perform climb adjustment.

Adjust for the desired response so that the carburetor is not flooded within the points

4~6 range.

Flying range

Points 7~9 are the flying range. Point 9 is the maximum speed needle. Therefore,

adjust the connection from hovering to maximum speed with points 7 and 8. Slowly

set the throttle stick from hovering to full close and adjust the high side mixture. With

the stick fully closed, fly at high speed and set the needle, while paying attention to

the change in the sound. Finally, carry out hovering and flying adjustment and finish

by fine adjusting to the best mixture. When flying, the entire high side can be con-

trolled based on point 5 and needle changes caused by temperature changes can be

adapted to by using the VR set with the model menu (MDL) fuel mixture (FMC)

item.

5 Condition setup

(1) When the condition menu (CND) is called and the fuel mixture "FMC" function is

selected, the FUEL MIX item is displayed.

-This item enables setting of each condition. Set each condition matched to the number of conditions used.

CAUTION: Conditions setting is a condition.

(2) Set MST MIX MODE (master mix mode).

-This mode operates by mixing throttle and mixture. However, what is operated is decided individually. Usually,

this is used with "MIXED".

-When used with "MIXED", when the throttle curve is set, the mixture curve is simultaneously mixed and

changed. (The mixture curve can also be set in the mix mode "MIXED".)

-When used with "UNMIXED", throttle and mixture control are set independently. When a tuned silencer is used,

etc., the fuel can be adjusted independently and the adjustment width is widened. Since all mixture adjustments

are carried out independently, learn the functions before trying to make any adjustments.

(3) Set the mixture curve with the POINT item.

-Nine points, from point 1 to point 9, can be set. The smaller displayed value is the direction in which the needle

is closed and the larger displayed value is the direction in which the needle is opened.

-Set the basic curve data by referring to the values shown below. However, this setting is a little dense.

Reference values (OS carburetor)

(4) The setting range is divided into an idling area, hovering area, and flying area.

Point P1 P2 P3 P4 P5 P6 P7 P8 P9

Set value (%) 15 36 50 58 64 68 73 76 80

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

9ZAP 9Z World Champion Model 2 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info