554174
7
Zoom out
Zoom in
Vorherige Seite
1/25
Nächste Seite
7
Device diagram
1 Wall plate 2 Piezo emitter
3 Jumpers 4 Mainboard
5 Battery connection 6 Cover tamper contact
7 Battery pack 8 Spirit level
9 Housing screws 10 Cover
11 Housing screw holder 12 Wall break contact
13 Lens 14 Flashing LED bar
Installation
Using the wireless testing box, determine a suitable location for the wireless external siren. Make sure that the siren is
mounted out of arm's reach (at least 3 metres above ground level). The siren should also be visible and audible from a
long distance.
In order to guarantee problem-free operation, the siren must NOT be mounted in the following locations:
Next to large metal structures (e.g. metal doors and frames, water tanks, vehicles and refrigerators).
Next to the main power, water or gas lines.
Within a metallic housing.
Next to electronic devices, especially computers, photocopiers and radios.
Opening the housing and inserting the batteries
1. Remove the covers on the two housing screws. Loosen the screws until the siren can be opened.
2. Hinge the cover to the side and remove it.
3. Insert both alkaline battery packs from the side into the battery holders. Use the attached clip to feed the battery
cable.
4. Connect the battery cable to the connections on the siren mainboard, paying attention to the correct polarity.
Incorrect polarity can damage the battery or the siren.
5. When replacing the battery, first remove the cable from the connection on the mainboard. Pull the cable through
the clip. Press the movable part of the battery holder downwards and remove the battery packs.
Pre-drilled holes for wall assembly are found on all four corners of the siren wall plate. Only use the enclosed screws
and wall plugs for assembly. The built-in spirit level above the battery compartment facilitates the alignment of the
siren. The length of the wall tamper contact can be set individually. This is made by trimming the pin.
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Abus FU8220 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info