Bedienungsanleitung Acson NET3-0808 (Seite 5 von 44) (Englisch)

646707

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

1.1 ON/OFF Button

• Starting Operation:

When the unit is turned off, press the ON/OFF button.

The operation LED lights and the unit is turned on.

• Stopping Operation:

When the unit is turned on, press the ON/OFF button. The operation LED is extinguished

and control are turned off.

1.2 SLEEP Button

Press SLEEP button to activate the sleep mode or energy saving mode.

1.3 FAN Button

Press FAN button to select

AUTO

HIGH

MEDIUM

LOW

fan speed.

1.4 MODE Button

Press the MODE button to switch operation from

COOL

HEAT

AUTO, DRY

FAN

The Auto mode is unavailable for Chilled Water (CW) system.

Check the display to see in which mode the control is set.

1.5 ‘▲’ or ‘▼’ Set Temperature Button

Press the temperature button and set the temperature of your choice. By pressing the ‘▲’ or

‘▼’ button once, temperature changes by 1°C [or 1°F].

Temperature can be set within the range 16°C~30°C (61°F~86°F) or 20°C~30°C (68°F~86°F).

The range can be set by adjusting the shunt jumper behind the LCD remote (refer table below).

During fan mode, temperature can not be set.

If pressing ‘▲’ and ‘▼’ together, the unit of temperature will change from °C to °F and

vice-versa.

1.6 SWING button

Press SWING button to activate the air sweep function.

1.7 Time Setting

i) Set Real Time Clock Setting

Press CLOCK key one time will activate RTC setting mode. Pressing the same key again

will disable RTC setting mode.

Under RTC setting mode, “SET CLOCK” will be shown on LCD and it will blink at 0.5 sec

interval. The RTC and Day setting can be changed by pressing DAY key, HOUR key or

MINUTE key. If there is no further time related (DAY, HOUR and MINUTE) key is pressed

for 15 sec, the unit will quit from the CLOCK setting mode.

ii) 7-Day Programmable Timers

The unit has 3 event functions, each event has an ON TIMER and an OFF TIMER.

Press the timer key (ON TIMER or OFF TIMER) will enable Event 1 timer setting mode.

Press the same key again will enable Event 2 timer setting mode. Press the 3rd times will

enable the Event 3 (Event handset) timer- setting mode. Subsequent key pressed the unit

will quit from timer setting mode.

All timers are event triggered timers and can be overridden by the ON/OFF button and

Override function.

iii) Set Event 1 and Event 2 Timers

Under timer setting mode, “SET TIMER” will be shown on LCD and blink at 0.5 sec interval.

For Event 1 Timer setting, ‘ ON’ or ‘ OFF’ indication will appear and digit “1” will be

displayed on the top left corner of the LCD. ‘ ON’ or ‘ OFF’ indication and digit “2”

will be displayed during Event 2 timer setting. The timer setting can be changed through

pressing the DAY key, HOUR key or MINUTE key. If there is no further time related (DAY,

HOUR and MINUTE) key is pressed, the unit will quit from the timer setting mode.

Jumper 20 - 30 Application

SET Set temp range : 20°C ~ 30°C (68°F ~ 86°F)

OFF Set temp range : 16°C ~ 30°C (61°F ~ 86°F)

1 OM-NET3-0808_EN 9/5/08, 12:00 PM2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Acson NET3-0808 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info