Bedienungsanleitung ACV HEATMASTER 100 N (Seite 4 von 26) (Englisch)

524656

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

ENFRRU PL DE IT ES NL

EN • 4

664Y5400•B

USER'S GUIDE

USING THE BOILER

Make sure to have your installation inspected and

maintained, if required, at least once a year by an

approved and qualified engineer. More frequent

servicing may be required depending on boiler use. If

this is the case, consult your installer for advice.

Starting the burner:

In normal operation, the burner starts automatically

as soon as the boiler temperature drops below the set

temperature.

GETTING FAMILIAR WITH THE CONTROL PANEL

The user must not attempt to gain access to the components inside the

control panel.

• Master switch

Is used to turn the HeatMaster® on or off.

• Control thermostat - 60-90 °C

When using the HeatMaster® as a hot water generator only, the

temperature can be set between 60 °C and 90 °C. If the HeatMaster®

is used for both domestic hot water (DHW) and central heating, the

control thermostat would normally be set at 80 °C to achieve optimum

operating conditions.

• Summer/winter switch

Is used to turn the heating pump (if fitted) on or off.

• Manual reset high limit thermostat

If the boiler temperature exceeds 103 °C, this safety device will activate

and the high temperature indicator will light up. To reset - first allow the

boiler to cool to below 60 °C, unscrew the cap and press the reset button

using a pencil or similar pointed device, then reinstall the cap. If the fault

persists, turn the boiler off and call a service engineer.

• Daily timer

Allows the HeatMaster® to be turned on and off at specific moments of

the day and operates on a 24 hour sequence. A series of white tabs are

set around the timer, each tab corresponding to a 15 minute switching

period. To set the timer, simply push outwards the number of tabs

required for ON period.

Remember: Tab in = HeatMaster® OFF

Tab out = HeatMaster® ON

• Temperature and pressure gauge

This gauge indicates both the temperature of the HeatMaster® and the

pressure within the primary circuit. The temperature should not exceed

90 °C - if it does, switch the boiler off and check the thermostat setting.

If the fault persists, call an engineer. The pressure should not fall below

1 bar, if it does, please see the ‘Heating System Pressure’ paragraph

further in this section.

• Low primary water pressure indicator

If this indicator lights up, the primary circuit of the HeatMaster®

requires topping up with water. Please see the ‘Heating System

Pressure’ paragraph later in this section.

1. Burner safety cutout warning indicator

2. Low primary water pressure indicator

3. High limit thermostat indicator

4. Temperature and pressure gauge

5. Control thermostat

6. Daily timer

7. Manual reset high limit thermostat

8. Master switch

9. Summer/winter switch

HeatMaster® 30 N and 60 N Control Panel

8 9

HeatMaster® 70 N and 100 N Control Panel

8 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ACV HEATMASTER 100 N Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ACV HEATMASTER 100 N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info