Probe:2xAAA50/60Hz + 2xAA
Station:100-240V 50/60Hz + 3xAAA
TECHNICAL DATA
To check the Alarm setting. In default mode, press the „Mode”(1a) button twice.
2.5 Alarm time check.
To check the Date. In default mode, press the „Mode”(1a) button once.
2.4 Date check
* Outdoor temperature upper limit: 70C, lowest limit: -40C.
* Indoor temperature upper limit: 50C, lowest limit: 0C.
2.5 Temperature and Humidity Function
* Out of the indoor and outdoor temperature display, the low-end displays “Lo”, the high-end displays “Hi”. You can check the lowest and highest recorded
temperatures by pressing the „Max/Min” briefly to cycle between them.
b.10-20 seconds after the alarm starts, the device will make a noise 2 time per second
c. Over 20 seconds after the alarm starts, the device will make a noise 4 time per second
The alarm has 3 settings.
a.0-10 seconds after the alarm starts, the device will make a noise 1 time per second
* Snooze could be repeated all the time.
You can turn on the snooze function without limit.
To change the backlight strength press “SNOOZE/LIGHT”(1f) once. The device has 2 settings. 1. Maximum backlight 2. Minimum backlight.
After 2 minutes of working the alarm will shut down of its own accord.
When the alarm turns on you can press. “ALARM”(1d) button to shut it off. You can also press the “Snooze”(1f) button. It will turn off again after the
*Snooze* time runs out after 5 minutes.
2.3 Alarm ON/OFF
Setting in sequence: Alarm Hour→Alarm Minute →Exit
AL2 Setting is the same as the AL1 setting.
After 10 seconds of not pressing any button, the device will exit the change mode and will save all current settings that were changed to that point.
After setting, press “ALARM”(1d) to confirm and exit.
Press “DOWN”(1c) once and back; press and hold for 2 seconds, go back at an 8 step per second speed.
Press “UP”(1b) key, the value goes ahead one step; press and hold for 2 seconds, go ahead at an 8 step per second speed.
Setting item blinking at 1s frequency.
Press and hold “ALARM”(1d) Button for 2 seconds and the first digit of the setting will start to Flash.
To turn on alarm press the “ALARM”(1d) button once. The alarm icon will appear above the time and the last alarm setting will appear.
2.2 Alarm Setting
Hour FORMAT 24/12h → Hour → Minute→ Year→ Month→ Day→ Temperature format C/F→ Exit
The order of the setup goes as follows:
After 10 seconds of not pressing any button, the device will exit the change mode and will save all current settings that were changed to that point.
After setting, press "MODE"(1a) to confirm/exit.
Press the “DOWN”(1c) key, the value goes down one step; press and hold for 2 seconds, go back at 8 steps per second speed.
Press “UP”(1b) key, the data goes up one step; press and hold for 2 seconds or more, it will go ahead at 8 steps per second speed.
Setting item blinking at 1s frequency.
2.1 Time Setting
Into the probe insert 2x AAA battery.
Insert the battery (2xAA) into the device or connect adapter after a few seconds, LCD will light up, after a beep, it enters default mode.
2. Operation Instruction
1. Clock 2.Inside temperature 3. Outside temperature 4. Probe 5. Weather Forecast 6. Alert Indicator
Display:
Description of the device. ( Weather Station)
1. Control panel: Buttons 1.a. MODE, 1b.UP, 1.c. DOWN, 1.d. ALARM, ,1E. Max/Min 1G. SNOOZE/LIGHT，
batteries inside.
Under default state, press and hold "MODE"(1a) for 4 seconds to enter setting in sequence, the time will start to flash.
4
