Bedienungsanleitung Adtran total access 1500 dual ds0 dp (Seite 3 von 14) (Englisch)

429061

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

61180019L1-5A Issue 1, May 2004 3

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired

operation.

Changes or modifications not expressly approved by

ADTRAN could void the user’s authority to operate this

equipment.

2. INSTALLATION

After unpacking the Total Access 1500 19-Inch

Chassis, inspect it for damage. If damage has occurred,

file a claim with the carrier, then contact ADTRAN

Customer Service. Refer to the Warranty and Customer

Service section for further information. If possible, keep

the original shipping container for returning the 19-Inch

Chassis for repair or for verification of shipping

damage.

NOTE

This product is intended for installation in

restricted access locations only.

CAUTION

Electronic modules can be damaged by ESD.

When handling modules, wear an antistatic

discharge wrist strap to prevent damage to

electronic components. Place modules in

antistatic packing material when transporting

or storing. When working on modules, always

place them on an approved antistatic mat that is

electrically grounded.

WARNING

To prevent electrical shock, do not install

equipment in a wet location or during a

lightning storm.

Tools Required

The required tools for the Total Access 1500 19-Inch

Chassis installation are as follows:

• Wire-wrap tool

• #2 phillips-head screwdriver

• #1 phillips-head screwdriver

• Straight-slot-head screwdriver

• Multimeter

• Crimping tool for power lugs

• Wire strippers

• Side cutters

• 3/16-inch wrench

Material that should be on hand includes the following:

• Four screws for mounting each Total Access 1500

19-Inch Chassis to the rack

• Shielded 2-wire, twisted pair cross-connect wire

with drain, such as AT&T P7 wire

• Insulated wire for power connections

• Insulated wire for frame ground

• Lugs for the power wire and Frame Ground

connection

Unpack and Inspect the Chassis

Each Total Access 1500 19-Inch Chassis is shipped in

its own cardboard shipping carton unless it was ordered

as a fully racked cabinet or wall mount system. Open

each carton carefully and avoid cutting too deep into the

carton with sharp objects.

Mounting the Chassis

The Total Access 1500 19-Inch Chassis can be flush-

mounted or mid-mounted.

Mounting Bracket Orientation

The Total Access 1500 19-Inch Chassis comes with

mounting brackets that can be mounted with the flanges

facing forward or backward in two different locations

on the chassis sides. This allows the chassis to be flush-

mounted or mid-mounted. Attaching the mounting

brackets to the chassis requires three screws on each

side that are supplied with the unit.

The mounting brackets can be used for 19 or 23-inch

rack applications:

• The narrow side should be screwed to the chassis

for a 23-inch rack.

• The wide side should be screwed to the chassis for

a 19-inch rack

C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adtran total access 1500 dual ds0 dp Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info