Bedienungsanleitung AEG Oxygen - K (Seite 11 von 16) (Deutsch, Englisch)

551733

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

• Place the power unit in order to make the exhaust pipe

as short as possible. Exhausts should be limited to no longer

than 5 meters.

• Keep in mind that you may need space on the sides of your

central unit to be able to access the dirt receptacle.

Refer to page 14 - Image 6

• Align the power unit intake ﬁ tting to the main trunk line projecting

from the wall.

DO NOT GLUE. Attach the exhaust pipe to

the motor exhaust if exhausting outdoors. Make sure the exhaust

pipe is as short as possible.

NOTE: Mount central power unit at least 30cm from the ceiling

and any adjacent wall, at least 70cm from the ﬂ oor and within 1.8 m

of an electrical outlet. Review any local regulations that may apply.

Refer to page 14 - Image 2

WARNING

Do not block the hood ventilation openings on the top of the central

power unit. Lack of ventilation will cause the motor to overheat.

WARNING

Do not locate the central power unit in a high temperature area where

it is inaccessible for example, an attic or crawl space.

For the ultimate in air control you have the a true HEPA ﬁ lter and may

be included with your choice of power unit or can be purchased from

an authorized dealer/distributor. Simply attach the true HEPA ﬁ lter as

shown.

Refer to page 14 - Image 7

SYSTEM TEST

Be certain to comply with local electrical codes and regulations.

Plug the unit into a regular electrical outlet. You are now ready to

check the installation of the unit:

• Be sure the ﬁ lter is properly installed in the power unit.

• Be sure the dirt receptacle is properly secured to the power unit.

• Plug the hose into each inlet valve to be sure the electrical

contacts operate properly.

• Check each inlet valve for air leaks.

• Check each pipe connection for air leaks.

Refer to page 14 - Image 8

HOW TO USE CENTRAL VACUUM SYSTEM

Your central vacuum system is controlled by a switch on your

hose. Simply insert the hose into the valve and turn the switch to

the on position. This will start the power unit and the ﬂ ow of air.

When you are ﬁ nished, turn the switch on the hose to the

off position and remove the hose from the inlet valve. When

unplugging the hose, hold the inlet cover open for a few

seconds to allow suction to decrease thus, protecting the

inlet valve seal.

Refer to page 14 - Image 8

LED INDICATIONS - OPTIONAL DEPENDING ON MODEL

You machine may be equipped with some or all of the indicators

listed below.

Refer to page 14 - Image 9

On/Off Motor Fault Dirt Receptacle Full Reset

Your power unit is equipped with a multi color LED panel. This LED

panel will provide you with necessary information on your power unit’s

performance, maintenance and diagnostics. Below are descriptions

of the different messages the power unit will provide.

NORMAL OPERATION

When the power unit is OFF and considered to be in standby mode

the LED button will be RED.

When the power unit is ON and in use the LED will be GREEN.

When the motor fault light is ON see further description below.

When the dirt receptacle light is ON, empty dirt receptacle, press the

RESET button and hold for 10 seconds.

MOTOR FAULT

In the case of a blown fuse or disconnected motor wire and the

power unit is not functioning the ON/OFF button will be constantly

GREEN In the case of an over current shutdown, the ON/OFF

button will be ﬂ ashing RED, the GREEN light will on and off rapidly

and the MOTOR FAULT light will be AMBER and turn on and off

rapidly. This fault will reset automatically in 15 seconds if the low volt

connection is OFF at the hose.

In the case of a continued over current and the low volt connection

is ON and the hose the ON/OFF button will constantly be RED,

the GREEN light will ﬂ ash slowly and the MOTOR FAULT will slowly

ﬂ ash AMBER.

In the unlikely event of a bad frequency received by the power unit

the power unit will not start and the ON/OFF button will remain

constantly RED. In the case of a high line voltage received by

the power unit the ON/OFF button will alternate between RED

and GREEN three times- pause brieﬂ y – alternate between RED and

GREEN three times – long pause- and then repeat. This will

continue until the line voltage returns to the correct level.

LCD SCREEN - OPTIONAL

Refer to page 14 - Image 8

In the main screen of the LCD, the AEG-Electrolux logo will appear.

This logo may scroll from side to side to avoid the image ingraining

itself onto the LCD Display. You will see the logo when the power

unit is not in use.

The button that best lines up with the Power symbol on the screen

can be used to activate the unit. Press this button to toggle the unit

on/off. The unit may also be activated from any installed inlet.

When you LCD power unit is in standby mode the four white lights on

your LCD unit will light up in sequence and alternate moving from left

to right then reversing right to left. This pattern will repeat continuously

and is an indication that your power unit is ready for use and

functioning properly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG Oxygen - K Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG Oxygen - K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info