382751
5
Zoom out
Zoom in
Vorherige Seite
1/64
Nächste Seite
4
ENGLISH
STEP 570 X, STEP 600 X
The stroke rate appropriate to the material being worked on can be taken from the
following table, and the corresponding letter shown on the setting wheel.
Material Stroke rate
Wood G
Steel D-E
Aluminium D-E
Rubber A-C
Intermittent use
Switching on: Press On-/off switch
Switching off: Release On-/off switch
Continuous use
Switching on: Press the On-/off switch and
then the locking button, after that release
on-off switch.
Switching off: Press the On-/off switch and
then release.
By adjusting the pendulum action the cutting depth of the saw blade teeth is
increased or decreased. As a rule of thumb:
Soft material Large pendulum stroke
Hard material Small or no pendulum stroke
Clean cut surface No pendulum stroke
The appropriate degree of pendulum effect can be taken from the following chart
and compared with the marking at the pendulum stroke lever.
Material Degree of swing action
Wood I - III
Plastic I
Aluminium 0 - I
Steel 0
Ceramics 0
Rubber 0
The stroke rate shown in the chart is only
a suggestion for your general guidance!
The stroke rate can be set on the stroke rate control even while the motor is
running.
1. Set the stroke and pendulum stroke according to the material to be cut.
2. Position the machine with the front part of the base plate on the material, and
switch on.
3. Press the machine downwards onto the material and guide it along the cutting line.
Do not press down too hard on the piece you are cutting. Light pressure on the saw
blade is sufficient to achieve the optimum rate of sawing.
When cutting along a score line, use the marking on the anti-splintering device as an
optical guide.
To obtain a perfectly straight cut, clamp a strip of wood as a guide along the material
or use the parallel guide (accessory).
For cutting at an angle, or cutting a bevel, adjust the base plate.
For sawing close to the edge, set the base plate at its rearmost position.
On-/off switch
Adjusting the
pendulum stroke
Advice for
operation
Hints
B
A
B
A
1
2
15
0
III
II
I
0
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für AEG step 600 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info