Bedienungsanleitung AEG WS 715-115 (Seite 2 von 57) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Finnisch)

463269

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

ENGLISH 2 WS 650-115, WS 715-115, WS 715-125, WSE 800-125

Introduction

You demand the best and buy quality - quality provided by Atlas Copco. We have

built for you a reliable and lasting tool. Working effectively and without endangering

your health is only possible if this instruction for use is read carefully before first us-

ing the tool. We want to satisfy our customers and would like you to buy again AEG

Electric Power Tools from Atlas Copco.

Technical Data

Safety advice ■ Please pay attention to the safety instructions in the attached leaflet!

■ Do not pierce the motor housing as this could damage the double insulation (use

adhesives).

■ Always disconnect the plug from the socket before carrying out any work on the ma-

chine.

■ Only plug-in when machine is switched off.

■ Keep mains lead clear from working range of the machine. Always lead the cable

away behind you.

■ Before use check machine, cable, and plug for any damages or material fatigue. Re-

pairs should only be carried out by authorised service agents.

■ Allow the machine to come to a stop before putting down.

■ Dust that arises when working in stones with crystalline silicic acid can damage your

health. Do not work on any material containing asbestos. Please note the safety reg-

ulations, VBG, of the employer’s liability insurance association.

■ Never reach into the danger area of the machine when it is running.

■ Always wear safety goggles and ear protectors when working with this machine. It

is further recommended to wear safety gloves, apron, as well as sturdy non-slipping

shoes.

■ Always use the additional handle.

■ Always use the protecting cap when roughing-down and separating.

■ Only use tools whose permitted speed is at least as high as the highest no-load

speed of the machine.

■ Check grinding tools before use. The grinding tool must be properly mounted and

turn freely. Perform a test run for at least 30 seconds without load. Do not use dam-

aged, out of round or vibrating grinding tools.

■ When grinding metal, flying sparks are produced. Take care that no persons are en-

dangered. Because of the danger of fire, no combustible materials should be locat-

ed in the vicinity (spark flight zone). Do not use dust extraction.

■ Due care should be taken that no sparks or sanding dust flying from the workpiece

come into contact with you.

■ Pay attention to the dimensions of the grinding disc. The mounting hole diameter

must fit the mounting flange without play. Do not use reducer pieces or adapters.

■ Never use a cutting disc for grinding. Do not subject cutting discs to side pressure.

■ When separating stone the guide shoe must be used!

Type WS 650- WS 715- WSE 800-

115 115 125 125

Nominal power (W) 650 710 710 800

Min. no-load speed (min

-1

) 2700

Max. no-load speed (min

-1

) 10000 10000 10000 10000

Grinding disk diameter (mm) 115 115 125 125

Thread of work spindle M14 M14 M14 M14

Weight (kg) 1,5 1,5 1,5 1,5

Speed control

•

No-load speed limiter

•

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG WS 715-115 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info