Bedienungsanleitung Akai DEEP IMPACT SB1 (Seite 2 von 7) (Deutsch, Englisch, Französisch)

630572

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

English

Power requirements for electrical equipment vary from area to area. Please ensure that your AC

Adaptor supplied meets the power requirements in your area. If in doubt, consult a qualified electrician

or AKAI professional dealer.

120 VAC @ 60 Hz for USA and Canada AC Adaptor MP-9 (CA)

220~230/240 VAC @ 50 Hz for Europe AC Adaptor MP-9 (EVB)

PROTECTING YOURSELF AND THE SB1 DEEP IMPACT

• Never touch the AC Adaptor with wet hands.

• Always disconnect the AC Adaptor from the power supply by pulling on the adaptor/plug, not the

cord.

• Allow only an AKAI professional dealer or qualified professional engineer to repair or reassemble

the SB1 DEEP IMPACT. Apart from voiding the warranty, unauthorized engineers might touch live

internal parts and receive a serious electrical shock.

• Do not put, or allow anyone to put any object, especially metal objects, into the SB1 DEEP IMPACT.

• Use only a household AC power supply. Never use a DC power supply.

• If water or any other liquid is spilled into or onto the SB1 DEEP IMPACT, disconnect the power, and

call your dealer.

• Make sure that the unit is well-ventilated, and away from direct sunlight.

• To avoid damage to internal circuitry, as well as the external finish, keep the SB1 DEEP IMPACT

away from sources of direct heat (stoves, radiators, etc.).

• Avoid using aerosol insecticides, etc. near the SB1 DEEP IMPACT. They may damage the surface,

and may ignite.

• Do not use denaturated alcohol, thinner or similar chemicals to clean the SB1 DEEP IMPACT. They

will damage the finish.

• Modification of this equipment is dangerous, and can result in the functions of the SB1 DEEP

IMPACT being impaired. Never attempt to modify the equipment in any way.

• Make sure that the SB1 DEEP IMPACT is always well-supported when in use on a firm level

surface.

• In order to assure optimum performance of your SB1 DEEP IMPACT, select the setup location

carefully, and make sure the equipment is used properly. Avoid setting up the SB1 DEEP IMPACT

in the following locations:

1. In a humid or dusty environment

2. In a room with poor ventilation

3. On a surface which is not horizontal

4. Inside a vehicle such as a car, where it will be subject to vibration

5. In an extremely hot or cold environment

• Be sure to wait for a few seconds before tuning the unit on again after the power has been turned

off to ensure proper operation.

• When you connect this unit to other equipment, make sure that all of the other equipment is turned

off in order to prevent malfunction or damage to speakers.

WARNING

The SB1 DEEP IMPACT is designed to be used in a standard household environment.

English

If you’re a bass player who loves those classic

synth bass lines but never wanted to learn to use

a keyboard, the DEEP IMPACT SB1 is just what

you’ve been waiting for: your favorite synth bass

sounds at the tips of your fingers. With 9 pro-

grammable presets to choose from, you can just

plug and play or shape the sounds to suit you.

With the true/clean bypass mode, when you turn

the effect off, there is no coloration of the sound from the input.

OUTPUT

This connects to your amp or to the input of another effect.

PROGRAM DOWN input

You can connect a separately sold footswitch here to decrement the program

numbers.

DC IN

Plug the supplied MP-9 (9-volt) AC adaptor in here.

INPUT

Plug your bass in here.

5 7

12 13

8 9 10

English

OUTPUT LEVEL control

This sets the output level (volume) of the effect.

PARAMETER selector

To select the parameters that you want to edit.

INPUT LEVEL control

This sets the input signal level.

Set it so that the red LED (OVER) doesn't light even when playing at your loudest.

Level meter: The LEDs show the following levels for the input signal:

Red - overload, level is too high / Yellow - correct level / Green - signal is too low

Note: It is important that the correct level (yellow) is set: If the level is too high, the

sound will be distorted. If the level is too low, the pitch will not be detected correctly

and the effect will not work properly.

PROG. NO display

Displays the program number.

DATA display

Displays the data value of the currently selected parameter.

DATA control

Turn this dial to adjust the parameter’s data value (select the parameter with the

PARAMETER selector).

LED (red)

Lights when the effect is turned on.

PROGRAM UP footswitch

Switches through the 9 programs.

The programs are selected from 1 through 9 and back to 1, you cannot select

lower program numbers (from 8 to 7 for example) unless a separately sold pedal

is connected to the PROGRAM DOWN input.

ON/OFF footswitch

Switches the effect on and off. Also used as an ‘enter’ button after a program has

been selected with the PROGRAM UP switch.

English

Operation:

1. Connect your bass to the INPUT jack.

2. Connect the OUTPUT jack to your amps INPUT jack or to the input of another

effect unit.

3. Turn your system on.

4. Press the ON/OFF (right) footswitch to turn the effect on (the LED (red) will light).

5. Adjust the INPUT LEVEL and OUTPUT LEVEL while playing the bass. The input

level should be adjusted so as the red LED of Level meter does not come on when

playing at your loudest. However, since the pitch cannot be determined properly if

the level is too low, the level should be adjusted as high as possible without turning

on the red LED (see “Important note” below for more detailed information).

Note: When the effect is turned off, the level display will not light. This is because

the SB1 is a true bypass and does not color the original sound of your bass when

turned off.

6. Select a program with the PROGRAM UP (left) footswitch.

The number will flash but the sound will not change. This is so that you can go

directly to a program without having to hear the other effects in between.

7. Press the ON/OFF switch to enable the selected effect (the number will stop

flashing).

Important notes:

• The SB1 performs the pitch detection of incoming signal. Depending on your

playing style, e.g., chord play, chopping, extremely fast passage, stc., the

pitch may be detected incorrectly and the effect sound may not sound at the

correct pitch.

• The SB1 is designed for bass. It can only handle the input signal of frequency

range between 30Hz and 470Hz (equivalent to the open 6th string note to

23rd fret of 1st string of a 6-string bass). If the incoming signal is outside this

range, it cannot detect the pitch correctly and so the synth sound (effect

sound) will be out of tune.

Akai DEEP IMPACT SB1 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info