630573
168
Zoom out
Zoom in
Vorherige Seite
1/170
Nächste Seite
156
Appendix
IDE/SCSI Conversion Kit
With the IDE/SCSI Conversion Kit, the IDE hard disk drive can be connected to the internal 50-pin SCSI
connector of the DPS12.
Consult your AKAI professional dealer where you purchased or the AKAI professional Service Center
for the installation of disk drive.
The self-installation may cause serious damages to both the disk drive and DPS12.
Notes:
Use ERASE, instead of FORMAT, to format the IDE drive. The IDE drive may freeze when FORMAT is
performed.
When ERASE is performed on the IDE disk that has been used on other device or brand new disk, an
error message may appear. In this case, perform ERASE again.
Consult your AKAI professional dealer or AKAI professional Service for the drives that can be installed.
Installation - To Service Technicians
IDE/SCSI Conversion Kit Installation
Install the IDE/SCSI Conversion Kit included to the IDE drive by the following procedure. The rest will be the
same as that of SCSI drive.
Note: Set the IDE drive in Master Mode referring to the drive’s manual.
Contents:
ID2SC PC board .................................................................. 1
PCB Mounting Bracket (L), (R) ............................................ 1
40P IDE flat cable ................................................................ 1
4P power cable .................................................................... 1
Plastic rivet........................................................................... 4
Drive Mounting screw (inch-thread 3.2 x 5) ......................... 8
Drive Mounting Plate screw (3 x 10) .................................... 4
Washer (2mm) ..................................................................... 4
ID2SC PCB Installation
1. Attach the PCB Mounting Bracket (L) and (R) to the IDE drive as illustrated. Refer to the direction of ID
hole to the connectors on the IDE drive. Use four inch-thread screws to fix them.
2. Connect the 40P IDE flat cable and 4P power cable to the ID2SC PC board. Place the cables between the
IDE drive and ID2SC PC board and fix the PC board to the PCB Mounting Brackets with plastic rivets.
Care must be taken to avoid pinching the wires by the PC board.
3. Connect the other end of cables to the IDE drive.
4. Set the DIP switch to the default setting as shown.
168

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Akai DPS12i wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info