228448
3
Zoom out
Zoom in
Vorherige Seite
1/9
Nächste Seite
Hardware requirements for existing telephone and safety advice:
Almost all wired telephones with a conventional handset and a plug-in handset cable can be connected.
Today nearly all modern home- and office telephones are equipped with a plug-in receiver cable (4 pin
Western” sockets). The BT 2000 only replaces the microphone and the earpiece of your telephone handset
so that you can move around within a range of several meters of your work place without any cables. You
can use the BT 2000 at analogue as well as ISDN- or proprietary telephone systems.
The following telephones can not be connected:
Designer telephones where additional electronic devices (i. e. buttons, displays) are installed in
the handset
Telephones with carbon, dynamic or piecoceramic microphones (mostly older models) which are
not yet equipped with state-of-the art electret microphones
Telephones with special handsets
In case of doubt please contact the company that services your telephone system. Please use only
the supplied accessories. Operate the audio gateway only in connection with the specially designed
wall charger, other chargers may damage the set or cause undesired effects on the telephone line.
Never open the headset or try to change or even open the lithium battery by yourself!
Hint: The headset can also be connected with other appliances equipped with Bluetooth technology such
as mobile phones and future DECT-telephone systems with Bluetooth™ technology. In this case the audio
gateway will only be used to plug in the headset for charging, the handset cable connectors will remain
unused. Pairing has to be done according to the manuals of the respective manufacturer. Observe the
relevant chapter at the end of this manual.
Connecting the audio-gateway to your existing telephone
Unplug the cable of the handset you
presently use and insert it in the lateral
socket of the audio gateway (1).
Plug in one end of the supplied straight
telephone cable in the now free socket of
your hand receiver, the other end plug in the
free socket at the bottom of your audio
gateway. You can lead the cable outside via the
2 slots in the plastic. (2)
Connect the DC plug of the wall charger with
the socket marked „DC 5V at the right side
1
2
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Albrecht bt 2000 bluetooth wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Albrecht bt 2000 bluetooth

Albrecht bt 2000 bluetooth Bedienungsanleitung - Deutsch - 9 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info