Bedienungsanleitung Alecto FR113 (Seite 5 von 8) (Deutsch, Englisch, Holländisch, Französisch)

794953

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

USER MANUAL INTRODUCTION

The Alecto FR-115 is a PMR-446 walkie-talkie.

This walkie-talkie allows you to not only commu-

nicate with each other free of charge, but also

with other (Alecto) walkie-talkies provided they

meet the PMR-446 standard.

DISPLAY FUNCTIONS

VOX = Voice Controlled Transmitting

SCAN = Channel Scan

Channel number

CTCSS subcode

= Standby

Battery level = receiving

= Sending

Key lock

Set volume level

FUNCTIONS INSTALLATION

POWER:

The FR-115 is powered through 3x AAA penlite

batteries.

1. Open the battery compartment by pressing

the tab at the bottom of the battery cover

upwards, the battery cover can then be

removed.

In order to avoid the risk of

suffocation when used by small

children, because the belt clip is

a relatively small part, the belt clip

has been glued by the factory.

Removal and re-installation of the

battery cover may be more difficult.

2. Install the batteries according

to the markings in the battery

compartment and close the

battery compartment.

HEADSET:

On top of the FR-115 you’ll find the connector

for a headset with a 2.5mm plug. We advise you

to use an Alecto FRH-10 headset for this.

USE

Attention: for a connections between 2

walkie-talkies, both walkie-talkies must

be set to the same channel, with the same sub-

code. See further on in this manual how to set

the channel and sub-codes.

TO SWITCH ON/OFF:

Press and hold the button for 2 seconds to

switch the walkie-talkie on or off.

VOLUME CONTROL:

Repeatedly and briefly press the or button

to adjust the volume. The set volume level is

shown in the lower part of the display.

TO SEND:

Press the P button to send. Keep this button

depressed while speaking. Talk at a normal

voice volume and approximately 3 to 5 cm from

the walkie-talkie’s microphone.

TO RECEIVE:

Release the P button to receive.

CALL ALERT TONE:

Press the P button briefly to transmit a call alert

tone. This call alert tone is adjustable, see ‘To

change the call alert tone’ further on in this

manual.

BACKGROUND LIGHTING:

Each time you press a function button (except

the flash light button) the background lighting of

the display will illuminate. This lighting will auto-

matically switch off 10 seconds after pressing

the last button

FLASH LIGHT:

Use the button to switch on the built-in flash

light. This light remains lit for as long as you

keep this button depressed.

The walkie-talkie doesn’t need to be switched

on to use this function.

Attention: Don’t stare directly into the light when

lit and don’t shine it in other people’s eyes.

The light can be bright and may damage your

eyesight.

ADDITIONAL FUNCTIONS

VOX FUNCTION:

When the VOX function is enabled (VOX =

Voice Activated Transmission), the FR-115 starts

sending as soon as you speak into the micro-

phone.

To switch the VOX function on/off:

1. press 3x the MENU button, the word “VOX”

will illuminate in the left part of the display

2. use the buttons or to set the trigger sen-

sitivity (‘OF’ is off, ‘1’ is the lowest sensitivity,

‘3’ is the highest sensitivity)

3. press the P button to confirm

Preferably, use this function in combination with

headsets. Keep in mind that it can take over a

second after you’ve started talking before the

walkie-talkie enables the transmitter.

CHANNEL MONITORING: (listening)

Use this function to disable the noise reduction,

allowing you to also listen to weak transmitters

on the current channel.

To switch the MONITOR function on/off:

1. press and hold the button for 2 seconds to

disable the noise reduction and to monitor the

channel

2. release the button to turn the noise reduc-

tion on again

CHANNEL SCAN:

Use the scan function to listen in on all channels

one after the other.

1. Press and hold the button for 2 seconds to

start the scan

2. briefly press the or button to continue

scanning if you’re only receiving noise on a

certain channel

3. press the P or MENU button to end the scan

KEYPAD LOCK:

When the keypad lock is activated, the , and

MENU buttons are blocked.

1. press and hold the MENU button until

appears in the display after approx. 2 sec-

onds

2. press and hold the MENU button again for

2 seconds to release these buttons again

SETTINGS

TO CHANGE THE SEND/RECEIVE

CHANNEL:

1. press 1x the MENU button and the channel

indication starts flashing

2. press the or button to select the desired

channel

3. press the P button to confirm

TO CHANGE THE SUB-CHANNEL (CTCSS):

1. press 2x the MENU button and the sub-chan-

nel indication starts flashing

2. use the or button to set the desired

sub-channel (1-38) or disable this function by

selecting OF

3. press the P button to confirm

Keep in mind that the walkie-talkie at the receiv-

ing end must be set to the same sub-channel.

Sub-channel explanation, (CTCSS code):

Continuous Tone Controlled Squelch System

is a tone code that’s included while transmit-

ting. This tone code is not audible. Only when

the tone code of the transmitting walkie-talkie

matches the tone code of the receiving walkie-

talkie, the receiving walkie-talkie will reproduce

the signal. This prevents you from being dis-

turbed by other PMR-446 walkie-talkies commu-

nicating on the same channel.

SCAN

VOX

Microphone

Flash light

Headset output

Antenna

Display

P button

(send button)

Charging contacts

(rear)

Speaker

SCAN

VOX

1.5V AAA

FR-115

FR115

Alecto FR113 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info