Bedienungsanleitung Alecto HA-58 (Seite 9 von 10) (Deutsch, Englisch, Holländisch, Französisch)

708550

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

USE, TESTING AND MAINTENANCE:

USE:

The heat detector is operational if the 9 volt battery (6F22) is placed and the HA-58 is mounted to the ceiling. You

can only place the detector on the ceiling plate if the 9 volt battery is installed. If the detector is operational the red

LED will blink every minute. Once the measured temperature by the heat detector is higher than 55°C the alarm will

go off. A loud beep will sound and the red LED will blink continuously. Once the heat dissipates, the alarm will stop

automatically.

Testing:

By pressing the test key on the HA-58, the alarm can be tested to ensure it is still operational. Hold the key for at

least 2 seconds. Operation is correct if the red LED blinks and a tone is audible. Preferably check the detector

weekly. During alarm state, the HA-58 will generate a tone of at least 85dB(A) sound pressure. Do not test the heat

detector with candles, open ﬂames, cigarettes or similar methods. It is possible to test the heat detector with a hair

dryer.

ATTENTION:

• If there is any doubt over the cause of an alarm, then assume the alarm is caused by a re and evacuate

the premises as soon as possible.

• Keep the heat detector away from small children.

• During renovations, protect the heat detector against dust. It will lose it’s functionality if covered by dust.

Maintenance:

The HA-58 can be cleaned with a vacuum cleaner.

PLAN AN ESCAPE ROUTE:

• Make a map and mark all locations of doors and windows and a possible escape route. Note that you may need

an escape ladder on high ﬂoors.

• Ensure everyone in the house knows the sound the smoke alarms produce and regularly practice use of the

escape route.

• Leave the house immediately according to the plan when hearing the alarm. Every second counts: so respond

quickly. If you do not notice smoke or heat, check if everyone in the house is in a secure location.

• Do not open any doors without feeling wether the door is warm or if there is smoke coming from underneath the

doors. If it is, do not open that door. If the door is cold, put your shoulder ﬁrmly against the door and open it a

small amount to check for any heat or smoke ﬁrst.

• If there is much smoke, keep low and take shallow breaths, preferably through a moist towel. Call the ﬁre depart-

ment as soon as you are safe outside.

REPLACING THE BATTERIES:

The detector is supplied using a 9Volt blok battery. Only use the recommended type Pairdeer 6F22. Under normal con-

ditions the battery will last at least one year. If it is about to need replacement, the smoke detector will make a chirping

sound every 60 seconds for at least 30 days. Test the detector after every battery replacement. If the heat detector does

not function, please contact your supplier

ENVIRONMENT:

Do not throw away used batteries, but recycle them using your local chemical depot. Product may not be thrown out

as normal waste, but must be recycled as electrical waste.

SPECIFICATIONS:

Usage temperature ................................................................... 0˚C tot 60˚C

Power ....................................................................................... 9V DC batterij

Alarm point ............................................................................... 50~60 ˚C

Power usage in standby ........................................................... 15 µA max.

Sound level during alarm .......................................................... 85dB op 1 meter

Maximum distance from the wall .............................................. 7,5m

PROBLEM SOLUTION

No sound during the test procedure

Note: Hold the test button several

seconds during a test.

1. Remove the detector from the ceiling plate and check if the battery

is properly connected.

2. Clean the heat detector.

The heat detector beeps every minute Replace the 9V battery

The heat alarm regularly gives a false

alarm during cooking or during use of

the shower.

1. Clean the heat detector.

2. Move the heat detector to another location.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto HA-58 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info