Bedienungsanleitung Alesis VX49 (Seite 45 von 48) (Englisch)

693691

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Timing Functions

Overview

Between your VIP, your DAW, and/or an external MIDI device, your VX49 will be working within a setup that

requires a MIDI clock source. Here are some things to keep in mind when (1) selecting the MIDI clock source

and (2) adjusting/editing any timing-related settings in your setup.

Tempo

External MIDI Clock Source: To use your DAW or external MIDI device as your MIDI clock source, set

VX49’s Clock Source (in Global Mode) to External. Similarly, set the MIDI clock source in your DAW or

external MIDI device to send its clock information out. VX49’s Tap Tempo button will be disabled and its light

will remain off when using an external clock source.

Internal MIDI Clock Source: To use VX49 as your MIDI clock source, set its Clock Source (in Global Mode)

to Internal. Similarly, set your DAW and/or external MIDI device to receive clock information from VX49.

You can set VX49’s internal tempo in either of the following ways:

• Tap the Tap Tempo button at the desired rate.

• Adjust the Internal Tempo setting in Global Mode.

The tempo of the MIDI clock source affects VX49’s Arpeggiator and Note Repeat (Roll) features.

Tap Tempo

When VX49’s Clock Source (in Global Mode) is set to Internal, its Tap Tempo button will flash at rate the

current tempo. The button will be disabled and its light will remain off when VX49’s Clock Source is set to

External.

You can use Global Mode to customize the Tap Tempo button’s operation. Use Tap Average to set the

number of times you would need to press Tap Tempo for VX49 to detect and enter a new tempo. Use

Tempo LED to turn the button’s light On or Off.

You can also set a connected footswitch to act as the Tap Tempo button. See MIDI Edit Mode to learn how

to do this.

Time Division

VX49’s time division setting determines how each beat is divided. The setting is a subdivision of the tempo:

1/4, 1/4T, 1/8, 1/8T, 1/16, 1/16T, 1/32, and 1/32T (T denotes a triplet-based time division). This feature

works whether VX49’s Clock Source is set to Internal or External.

You can set the time division by pressing Time Div and pressing one of the 8 switches. Alternatively, set the

Time Division parameter in the configuration pages for the Arpeggiator or Note Repeat (Roll).

Transport Control

The four Transport Control buttons are dedicated buttons for sending conventional transport control

commands: Stop, Play, Record, and Loop (if your software supports this feature). You can use the

Transport Format setting (in Global Mode) to set these buttons to send MIDI (MIDI Start/Stop), CC (pre-

assigned MIDI CC values), MMC (MIDI Machine Control), and MMC/MIDI. The PTEX setting is for use with

Avid

Pro Tools

Express only: transport control messages will be sent only on USB Port B, Channel 16,

regardless of the Common Channel setting.

Important: Your software must be able to loop or repeat in order to use the Loop button. Also, configure the

Transport Format in Global Mode so it communicates properly with your software.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alesis VX49 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alesis VX49

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info