541359
15
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
iLive Fixed Format Getting Started Guide 15 AP7141 iss.5
Step 5 – Work with the channel processing
Access the Preamp, EQ and dynamics
Press a strip SEL key. Press the key again to turn it off or
press another to access a different channel.
* You can press and hold any SEL key in the Processing
Block to temporarily send it to the PAFL system to listen to
and meter the signal at that point in the signal path.
The Channel Processing Block displays the current
settings for that channel. Controls illuminate if available.
The TouchScreen provides an alternative graphical view
and access to the input and insert patching, delay setting
and changing the name and colour. Touch the screen to
open the different processing views. Touch All to return to
the overview page.
Note - To view the processing parameters on the screen
make sure all the screen keys are turned off. The SEL keys
will not access the processing if you leave the screen in
NAME/COLOUR, MIXRACK or SURFACE .
The
PREAMP screen lets you patch the Source to the DSP
channel, control the remote analogue mic preamp, adjust
channel Trim and Polarity, set name and colour, and adjust
the HPF (high pass filter).
Choose to present either the preamp controls (Gain, Pad,
48V, Polarity) or trim controls (Trim, Polarity) on the Surface
PREAMP section. This lets both FOH and Monitor engineers
work with their own independent trim controls once the Gain
has been set. All channels may be globally set to present
either the Preamp or Trim controls from the MIXRACK
SETUP / Mixer Pref screen. Once set, individual channels
may be changed from within their PREAMP screen
GEQ on faders
Press a mix master SEL key to access the processing for
that master. The GEQ is controlled from the screen or on the
faders by pressing the Surface GEQ FADER FLIP key.
Press again to return to normal fader mode. Press to toggle
between frequency banks on the smaller R72 and T80.
In GEQ on faders mode - The EQ frequencies are indicated
on the strip LCDs above. The strip meters display the RTA
(PAFL signal if one is selected). The red PK meters display
the dominant frequency if this option has been set in the
SURFACE / Preferences screen.
The fader on the right becomes the master or currently
active send level for the mix. Hold down ALT VIEW to
display the EQ dB settings on the strip LCDs. Press the strip
SEL keys to reset individual frequency bands to 0dB.
MUTE
SEL
MIXMIX
PAFL
Due to its compact size, the
smaller iLive surfaces do not
provide all the physical controls.
Access these parameters using
the TouchScreen.
* Processing SEL keys
Channel Processing Block
Preamp
SAFE
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Allen-Heath iLive wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info