541400
133
Zoom out
Zoom in
Vorherige Seite
1/134
Nächste Seite
Maintenance and Troubleshooting 133
Software Release 2.7.1
C613-02021-00 REV F
2. Check IPX circuit configuration
To check that the IPX circuits are correctly configured on each router repeat
steps 1 through 3 above, or enter the command:
SHOW IPX CIRCUIT
Check that there are two circuits, and for each circuit check that the circuit
is enabled, uses the correct interface and encapsulation (for Ethernet
interfaces), the network number is correct and “On demand” is set to “no”.
If not, then repeat steps 1 through 3.
3. Contact your authorised distributor or reseller for assistance
If you still have no visible routes to the remote router, contact your
authorised distributor or reseller for assistance.
Local Workstations Can Not Access Remote Servers
A number of different events can cause this problem. The following list of
events gives the most common:
1. Move workstation to server LAN
Check that when the workstation is moved to the same LAN as the file
server, it is able to access the server. If not, the fault lies with the
configuration of the workstation or file server. Check with your Novell
network administrator.
2. Check NET.CFG file
Take care with the workstation NET.CFG file. Always specify the
encapsulation (frame) as different LAN card drivers use different default
encapsulations.
3. Check for file server on Remote Office router
Does the file server appear in the IPX service table of the Remote Office
router? If the server does not appear in the table, its presence is not
advertised to the local LAN. To check this, enter the command:
SHOW IPX SERVICE
This should produce a display like that shown in Figure 26 on page 133. The
important point is that the file server must appear in the service table on the
Remote Office router and there must be a route to the file server’s internal
network number. If there is, and it still does not work, contact your
authorised distributor or reseller for assistance.
Figure 26: Example output from the SHOW IPX SERVICES command for a basic Novell IPX network
To interpret output from the SHOW IPX SEVICES command see the Novell
IPX chapter in the Software Reference.
IPX services
Name Age
Address Server type Circuit Hops Defined
--------------------------------------------------------------------------------
ACCOUNTS 0
00007500:000000000001:0451 0004:Fileserver 1 (eth0) 1 SAP
ACCOUNTS 0
00007500:000000000001:8104 0107:RCconsole 1 (eth1) 1 SAP
TYPISTS 0
00000012:0080488018d8:0451 0004:FileServer 1 (ppp0) 2 SAP
--------------------------------------------------------------------------------
133

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Allied Telesis AR441S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info