Bedienungsanleitung Alpina AHT 500 E (Seite 14 von 19) (Alle Sprachen)

731904

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

USING THE MACHINE / MAINTENANCE AND STORAGE 9

WARNING! For your safety and that of

others:

– After each use, disconnect the machine

from the mains and check for damage.

– Correct maintenance is essential to main-

tain the original eciency and safety of the

machine over time.

– Keep all nuts, bolts and screws tight to be

sure the equipment is in safe working con-

dition.

– Never use the machine with worn or dam-

aged parts. Damaged parts are to be re-

placed and never repaired.

– Only use original spare parts. Parts that are

not of the same quality can seriously dam-

age the equipment and compromise safety.

WARNING! During maintenance oper-

ations unplug the machine from the mains.

1. MOTOR COOLING

To avoid overheating and damage to the motor,

always keep the cooling air vents clean and free

of sawdust and debris.

2. MAINTENANCE AND SHARPENING

OF THE BLADE

WARNING!

Periodically check that the

blades are not bent or damaged and that the

xed comb on the blade is intact.

Adjustment of the distance between blades is not

necessary, as this is predetermined by the manu-

facturer.

If the blades are used correctly, following all the

instructions provided, they will not require any

maintenance work and will not need sharpening.

It is necessary to sharpen the blades only when

the trimming performance decreases and the

branches tend to stick together.

NOTE

Any intervention on the blade

should always be conducted at a specialised Cen-

tre that has the most appropriate tools and is able

to perform the operations without compromising

the safety of the machine.

3. ELECTRIC CABLES

WARNING!

Check the condition of the

The best results will be obtained with the blade

slightly inclined (5° - 10°) in the direction you are

cutting, proceed with a curved movement, slowly

and without interruptions, especially in the ca se of

very thick hedges.

4. LUBRICATING THE BLADES DURING

JOBS (Fig. 6)

If the trimming device overheats whilst working, it

is necessary to lubricate the internal surfaces of

the blades.

WARNING! This operation must only

be performed when the blades have stopped

running and the motor is switched o.

4. END OF OPERATIONS

When you have nished your work:

– Switch o the motor as indicated above (Chap.

6).

WARNING! Allow the motor to cool

before storing in any enclosure.

To reduce re hazards, clean the machine

thoroughly to get rid of any remains of grass,

leaves or excess grease, never leave contain-

ers with the cut debris inside the storage area.

To increase the eciency and working life of the

blades, clean and lubricate them carefully after

each work session.

– Use a soft cloth to clean the blades, along with

a brush to remove more dicult dirt and debris.

– Lubricate the blades with suitable, non-polluting

oil were possible.

8. MAINTENANCE AND STORAGE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpina AHT 500 E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info