471309
37
Zoom out
Zoom in
Vorherige Seite
1/42
Nächste Seite
35-EN
Installation
Caution
Do not block the unit’s fan or heat sink, thus preventing air
circulation. If blocked, heat will accumulate inside the unit
and may cause a fire.
1
Remove the Detachable Front Panel (refer to page 5). Slide
mounting sleeve from main unit. (see “Removal” on this
page).
Slide the mounting sleeve into the dashboard.
NOTE
Please examine the installation. Make certain that no external
pressure is applied to either the top of the unit or the removable
nosepiece.
2
Reinforce the head unit with the metal mounting strap (not
supplied). Secure the ground lead of the unit to a clean
metal spot using a screw (
) already attached to the
vehicle's chassis.
NOTE
For the screw marked
**
, use an appropriate screw for the
chosen mounting location.
Mounting Sleeve
(Included)
Dashboard
This unit
Connect each input lead coming from an amplifier or
equalizer to the corresponding output lead coming from the
left rear of the CDA-9827/CDA-9826/CDA-9825. Connect all
other leads of the CDA-9827/CDA-9826/CDA-9825
according to details described in the CONNECTlONS
section.
Slide the CDA-9827/CDA-9826/CDA-9825 into the
dashboard. When the unit is in place, make sure the locking
pins are fully seated in the down position. This can be done
by pressing firmly in on the unit while pushing the locking
pin down with a small screwdriver. This ensures that the
unit is properly locked and will not accidentally come out
from the dashboard. Install the Detachable Front Panel.
Removal
1 Remove the DETACHABLE FRONT PANEL.
2 Use a small screwdriver (or similar tool) to push the
locking pins to the “up” position (see above drawing). As
each pin is unlocked, gently pull out on the unit to make
sure it does not re-lock before unlocking the second pin.
3 Pull the unit out, keeping it unlocked as you do so.
<JAPANESE CAR>
Face Plate
NOTE
Secure the ground lead of the unit to a clean metal spot using a
screw (
) already attached to the vehicle's chassis.
3
Lock Pin
Mounting Bracket
Ground Lead
Screws (M5 × 8)
(Included)
This unit
Metal
Mounting
Strap
Chassis
Hex Nut (M5)
Bolt Stud
Ground Lead
∗∗
This unit
Screw
No Pressure Here
No Pressure Here
Air ventilation
hole
<Rear side>
37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Alpine CDA-9827 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info