Bedienungsanleitung Alpine CDE-135BT (Seite 18 von 46) (Englisch)

536969

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

18-EN

Setting the Treble Control

After selecting TREBLE from the 3BAND EQ adjustment

mode, turn the Rotary encoder to select the desired

Treble setting item, and then press ENTER.

WIDTH (Q)  CENTER FRQ  LEVEL

Turn the Rotary encoder to select the desired setting

value, and then press ENTER.

Press  to return to the previous step.

 Setting the Treble Bandwidth (WIDTH (Q))

Turn the Rotary encoder to select the desired treble

bandwidth.

WIDE 0.75  NARROW 1.25 (Initial setting)

 Setting the Treble Centre Frequency (CENTER FRQ)

Turn the Rotary encoder to select the desired treble

centre frequency.

7.5k (Hz)  10.0k (Hz) (Initial setting)  12.5k (Hz)  15.0k (Hz)

 Setting the Treble Level

Turn the Rotary encoder to select the desired treble level

(-7~+7)

You can emphasise or weaken the treble level.

* The adjustment can also be made by pressing AUDIO. Refer to

“Adjusting Subwoofer Level/Bass Level/Mid Level/Treble Level/

Balance (Between Left and Right)/Fader (Between Front and

Rear)/AUX Mix Level/Loudness/Defeat” on page 16.

The High Pass Filter on this unit can be adjusted to suit your personal

taste. This feature works best when used in conjunction with a

subwoofer.

 Setting item: HPF

Setting contents:

OFF (Initial setting) / 60 (Hz) / 80 (Hz) / 120 (Hz) / 160 (Hz)

All frequencies above the selected cutoff are output.

When the subwoofer is on, you can adjust the subwoofer output level

(refer to “Adjusting Subwoofer Level/Bass Level/Mid Level/Treble Level/

Balance (Between Left and Right)/Fader (Between Front and Rear)/

AUX Mix Level/Loudness/Defeat” on page 16).

 Setting item: SUBWOOFER

Setting contents:

ON (Initial setting) / OFF

ON:

The subwoofer signal is output from the Subwoofer RCA

Connectors (refer to “Connections” on page 44).

OFF:

No subwoofer signal is output from the Subwoofer RCA

Connectors (refer to “Connections” on page 44).

The Low Pass Filter on this unit can be adjusted to suit your personal

taste.

 Setting item: SUBW LPF

Setting contents:

OFF (Initial setting) / LPF 60 (Hz) / LPF 80 (Hz) / LPF 120 (Hz) /

LPF 160 (Hz)

All frequencies lower than the selected cutoff are output.

The subwoofer output phase is toggled SUBWOOFER NORMAL (0°) or

SUBWOOFER REVERSE (180°). To adjust the level, turn the Rotary

encoder. Depending on the installation location of your subwoofer, one

of these settings may sound better than the other.

 Setting item: SUBW PHASE

Setting contents:

NORMAL (Initial setting) / REVERSE

When the subwoofer is on, you can select either SYS 1 or SYS 2 for the

desired subwoofer effect.

 Setting item: SUBW SYS

Setting contents:

SUBW SYS 1 / SUBW SYS 2 (Initial setting)

SUBW SYS 1:

Subwoofer level changes according to the main volume setting.

SUBW SYS 2:

Subwoofer level change is different from the main volume setting.

For example, even at low volume settings, the subwoofer is still

audible.

Adjusting the High Pass Filter

Turning Subwoofer ON/OFF

Adjusting the Low Pass Filter

Setting the Subwoofer Phase

Setting the Subwoofer System

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine CDE-135BT Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine CDE-135BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info