Bedienungsanleitung Alpine CDE-135BT (Seite 37 von 46) (Englisch)

536969

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

37-EN

Notes

•  indicator lighting up means there is subcategory during search

mode.

 indicator lighting up means the current category is last search

hierarchy.

• While in the search mode, if you press and hold  for 2 seconds, or no

operation is performed for 60 seconds, the search mode is cancelled.

• In the search mode, pressing  will return to the previous search

hierarchy.

• Depending on the vTuner application, search category, search hierarchy,

etc., may differ.

• During last search hierarchy, press VIEW will change the display.

• In some cases, certain search mode may not work, or some stations

cannot play normally.

• The provided stations are subject to change, please visit the home page

of vTuner for the latest information.

Changing the Display

Press VIEW.

Notes

• Only alphanumeric characters can be displayed.

• The maximum number of characters is 128 (128 byte).

• Some characters may not be correctly displayed.

In Case of Difficulty

If you encounter a problem, please turn the power off, then on again. If

the unit is still not functioning normally, please review the items in the

following checklist. This guide will help you isolate the problem if the

unit is at fault. Otherwise, make sure the rest of your system is properly

connected or consult your authorized Alpine dealer.

No function or display.

• Vehicle’s ignition is off.

– If connected following instructions, the unit will not operate with

the vehicle’s ignition off.

• Improper power lead (Red) and battery lead (Yellow) connections.

– Check power lead and battery lead connections.

•Blown fuse.

– Check the fuse of the unit; replace with the proper value if

necessary.

• Internal micro-computer malfunctioned due to interference noise

etc.

–Press the RESET switch with a ballpoint pen or other pointed

article.

Unable to receive stations.

• No antenna or open connection in cable.

– Make sure the antenna is properly connected;

replace the antenna or cable if necessary.

Unable to tune stations in the seek mode.

• You are in a weak signal area.

– Make sure the tuner is in the DX mode.

• If the area you are in is a primary signal area, the antenna may not be

grounded and connected properly.

– Check your antenna connections; make sure the antenna is

properly grounded at its mounting location.

• The antenna may not be the proper length.

– Make sure the antenna is fully extended; if broken, replace the

antenna with a new one.

Broadcast is noisy.

• The antenna is not the proper length.

– Extend the antenna fully; replace it if it is broken.

• The antenna is poorly grounded.

– Make sure the antenna is grounded properly at its mounting

location.

CD Player not functioning.

• Out of operating temperature range +50°C (+120°F) for CD.

– Allow the vehicle’s interior (or trunk) temperature to cool.

CD playback sound is wavering.

• Moisture condensation in the CD Module.

– Allow enough time for the condensation to evaporate (about

1 hour).

CD insertion not possible.

• A CD is already in the CD player.

– Eject the CD and remove it.

Language

Genre Name

Station Name

Information

Basic

Radio

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine CDE-135BT Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine CDE-135BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info