Bedienungsanleitung Alpine mrd m 300 (Seite 23 von 24) (Deutsch, Englisch, Französisch, Spanisch)

168531

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

To find out more, visit www.alpinetechcenter.com

Kukje Printing Co., Ltd 127-2 Gamjeon-dong

Sasang-gu Busan Korea

Rev. A-101502

Printing in Korea (S)

68P02294K79-O

STEP 6. (6) TIME CORR. (Time Correction)

Due to the wide variety of installation and system design possibilities available, bass performance may not always

be optimized as a result of speaker placement relative to the listening position. Sound waves may not reach the

listener's ear at the same time as other speakers, especially in a multiple subwoofer configuration. Such differences

in phase can result in muddy (unclear) bass or even a complete cancellation in the frequency response. Therefore,

both the MRD-M300 and MRD-M500 are equipped with Digital Time Correction, making it possible to realign

subwoofer(s) in time. Proper use of this function will result in clear, powerful bass with a smooth transition to the

other speakers in the system. It is recommended to use the calculation formula provided in the owner's manual as a

starting point for this adjustment.

Congratulations on your new V12AccuClass-D

amplifier purchase. Before you get started, there are a few things

you should know about this unique amplifier that will help you optimize performance for your personal tastes or

particular application. Unlike traditional designs, the V12 AccuClass-D

amplifier employs a completely digital

internal architecture, utilizing both advanced DSP (digital signal processing) and amplification technologies. This

innovative design not only offers unparalleled tuning capability and accuracy, but also allows direct digital coupling

to the power output stage for cleanest and most powerful bass possible. As with any amplifier however, proper

setup is essential if you are to maximize your listening experience. Please read the quick explanation and setup

procedure for each feature listed on the following pages.

Important notes:

•

To maximize the output power from this amplifier, you must use a 2 ohm load.

•

Before adjusting the amplifier settings, set the signal source (head-unit) level to

minimize distortion.

•

It is best to utilize music that will represent your typical heavy bass listening

scenario when adjusting levels.

V12 AccuClass-D

Setup Guide

For MRD-M300, MRD-M500 and MRD-M1000 Amplifiers

STEP 7. (7) PHASE

Phase control allows you to flip the polarity of the subwoofer without actually reversing the physical connections.

This convenient feature is useful when the subwoofer is in a position that could result in some cancellation, causing

diffused, unclear bass. It is recommended to try both settings (0

/180

) to determine which is best for your

particular system.

STEP 8. (8) AMP SET (Amplifier ID No. /Turn-On Delay)

The Amp Set menu performs two functions. Firstly, by setting the amplifier ID number (1-8), it allows the optional

RACC (RUX-4280 Remote Amplifier Control Center) to identify each amplifier individually and in a specific order.

Secondly, it provides a variable turn-on delay that can be used to minimize inrush current in large multi-amp

systems, or to eliminate any turn-on “pop”.

STEP 0. (0) MEMORY

Memory Mode allows you to store all amplifier settings in an auxiliary backup memory. Once stored, additional

tweaks or adjustments can be made while retaining the ability to recall the original settings at a later time. Note:

This is simply a convenience feature, since all settings are saved in real time as adjustments are made, and will

remain even if power is lost during setup.

STEP 9. (9) OUTPUT DISABLE

Previously known as “Safe Mode”, this feature provides a simple way to safely adjust the all DSP functions with the

amplification circuit turned off, eliminating the possibility of speaker damage during setup. When set to “ON”, it

literally disables the high current draw output stage of the amplifier, while leaving the input and processing

sections active. Please note that this is the only amplifier function that does not engage/disengage in real time,

but requires the remote lead to be cycled off/on for the selection to take effect. Therefore, if it is accidentally set to

“ON” during programming, there will be no output the next time the amplifier is activated. Additional uses include:

bench setup with a low current DC power supply, amp valet, tuning or troubleshooting larger multiple

amp/subwoofer systems, etc.

DISP

Toggle

ENT

• Press and depress the "MODE" button until you are

in mode "9" (Output Disable).

• Push "ENT" and push "ENT" again to select "9-1" (ON/OFF).

• Toggle until "OFF" is displayed.

• Push "DISP" to exit.

Note: This setting will not take effect until the amp is

turned off and then on again.

SETTING SAFE MODE TO "OFF"

START HERE

1) Output Disable is on:

Go to Step 9 (Mode 9 on the amp) and set to “OFF”, then cycle amp power.

Subsonic and LPF frequency selections overlap or are too close together:

Adjust the crossover properly

3) If using RUX-4280 (RACC) remote subwoofer level is turned down :

Make sure the RACC is in normal

display mode (voltage or temperature) and adjust the level control.

4) Defective or broken RCA cables):

Replace RCA connectors

5) Blown fuse:

Replace Fuse with proper value

6) Remote trigger is not active:

Check remote turn-on lead with a voltage meter

7) Bad ground or power connection:

Check and replace ground connector

Typical causes for little or no output

NOTE: If using a RUX-4280 (RACC) with more than 1 AccuClass-D amplifier, be sure to set each amplifier with a

different ID Number (1-8). Amplifiers with the same ID will cause the RACC to display "NO AMP."

Alpine mrd m 300 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info