541754
4
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
4
REAR PANEL
1
2
3
3
54
7
8
8
8
8
8
8
8
8
9
9
11
10
6
3
3
1. POWER INPUT – Connect the included power cable to this input and connect the other
end of the cable to a power source. Make sure the top panel's POWER SWITCH is set to
"off" when plugging and unplugging the cable.
2. COOLING FAN – Keep the area in front of this vent clear from obstructions. The fan
behind the vent cools the amplifier, preventing overheating.
3. MIX OUT – Use standard balanced XLR cables
or balanced 1/4" mono TRS cables to connect
these outputs to the inputs of your active
loudspeakers.
4. SUB OUT – Use a standard balanced 1/4"
mono TRS cable to connect this output to the
input of an optional powered subwoofer.
5. LINK OUT – Use a standard unbalanced 1/4"
stereo TRS cable to connect this output to the
LINK IN of an optional second Kick amplifier (sold separately). When using this output, this
amplifier will be the "master"; it controls the audio, volume, etc. sent to the "slave" amplifier
connected to this output (each amplifier will output the same signal in parallel).
Alternatively, you may use a 1/4" stereo TRS splitter cable to connect this output to two
separate loudspeakers (left and right), two channels (left and right) of an external mixer,
etc.
6. LINK IN – Use a standard unbalanced 1/4" stereo TRS cable to connect this input to the
LINK OUT of an optional second Kick amplifier (sold separately). When using this input,
this amplifier will be the "slave"; its levels will be controlled by the "master" amplifier
connected to this input (each amplifier will output a summed mono signal).
7. MIC IN – Use a standard XLR cable to connect a microphone to this input.
8. LINE IN – Use standard 1/4" TRS cables to connect line-level instruments or sound
sources to these inputs. When connecting a mono sound source, use only the "L/MONO"
input.
9. AUX IN – Use a standard stereo RCA cable to connect a line-level sound source to these
inputs.
10. FOOT SW – You can connect a standard 1/4" TRS latching footswitch (sold separately) to
this input. A connected footswitch will allow you to activate/deactivate the amplifier's built-
in effects processor.
11. GROUND SWITCH – Depressing this switch grounds the amplifier, which can reduce hum
or noise.
Tip
(left channel)
Ring
(right channel)
Sleeve
(ground)
TRS connector
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Alto Professional Kick 15 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info