Bedienungsanleitung Amana bx 518 vw ve (Seite 3 von 180) (Englisch)

342869

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

1. Tape doors on top right and left corners to prevent

doors from opening unexpectedly.

2. Slide appliance cart under side of refrigerator opposite

hinges.

3. Wrap refrigerator with blanket or pad. Thread strap

around refrigerator. Put foam shipping pads, located in

shipping carton, under strap. Tighten strap securely.

Do not overtighten strap.

4. Lower appliance cart to floor with appliance cart

handles on bottom.

5. Remove top two bolts from skid.

6. Return refrigerator and appliance cart to an upright

position. Remove strap.

7. Slide appliance cart under opposite side of refrigerator.

8. Repeat steps 3-5.

9. Remove wooden base.

10. Return refrigerator and appliance cart to an upright

position. Move refrigerator in front of final location and

remove appliance cart.

2. Remove and reverse doors if necessary.

Some installations may require door reversal to achieve full

door swing. To reverse door swing direction perform the

following steps:

Tools Required

Wrenches and drivers as applicable

Phillips screwdriver

Blade screwdriver

Masking tape

IMPORTANT: For plug removal requiring use of flat blade

screwdriver or putty knife, blade of tool must be covered

with masking tape to avoid damage to refrigerator

finish. For plugs using a screwdriver or nut driver style

head, use appropriate tool to avoid damage to plugs.

1. Remove refrigerator handle.

• Remove handle screw

(C)

from top handle trim

(A)

Pry up edge of handle trim

(A)

using blade

screwdriver with blade covered with masking tape.

Remove handle

(B)

from door by removing 1

remaining mounting screw

(C)

at each end of handle.

• Remove 1 plug from top hinge side of door and 2

from front hinge side of door

(D)

. Replace 3 plugs in

empty mounting holes.opposite side of door using

mounting screws

(C)

2. Remove freezer door handle.

• Open freezer door 90°. Locate two notches on back

of freezer handle

(A)

. Insert flat screwdriver driver

blade wrapped in masking tape. Pry up back edge of

handle cap

(B)

and remove from handle.

• Remove handle

(A)

from door by removing two

mounting screws

(C)

• Remove 2 plugs

(D)

from opposite side of freezer

door and replace in empty mounting holes.

3. Remove top hinge cover. Top hinge cover snaps off.

Remove

" screws

(A)

to release top hinge

(B)

and

hinge shim

(C)

using hex nut driver. Remove and retain

all shims

(C & D)

4. Remove refrigerator door by lifting door off of center

hinge pin

(F)

and hex nut

(E)

. Inspect door to verify all

shims

(D)

are with hinge pin.

5. Remove center hinge pin

(F)

using hex nut driver. Due

to tight fit of pin, firm pressure may need to be applied.

Remove and retain all shims

(D)

6. Remove freezer door by lifting door off bottom

hinge

(K)

7. Remove center hinge bracket

(G)

and shim

(H)

using

Phillips screwdriver.

8. Remove toe grille and bottom hinge cover. Both snap

off.

9. Remove bottom hinge pin

(J),

bottom hinge

(K)

, and

hinge shims

(L)

using hex nut driver. Remove and

retain shims

(D)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Amana bx 518 vw ve Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info