Bedienungsanleitung Angelcare AC017 (Seite 5 von 28) (Englisch, Französisch, Spanisch)

681980

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

STEP 1  SETTING UP THE NURSERY UNIT

NURSERY UNIT:

Power ON/OFF Light Indicator

Low Battery Light Indicator

Battery Door

(2 AAA)

Power

ON/OFF

Pause/Pairing

Button

Nursery Unit Stand

Movement Sensor

Pad Sensitivity

Switch

Sensor Pad

light indicator

1.1  INSERT THE BATTERIES

When using the Nursery Unit for the ﬁrst time, you will need to insert 2 AAA alkaline batteries (not included).

1) Remove the battery door with screwdriver

and insert 2 AAA batteries.

1.2  SELECT A LOCATION FOR THE NURSERY UNIT

Nursery Unit can be installed using the tabletop stand.

Place the Nursery

unit at least 3 feet

(1 meter) from

the crib

STEP 2  POSITIONING THE MOVEMENT SENSOR PAD

2.1  POWERING THE MOVEMENT SENSOR PAD

When using the Sensor Pad for the ﬁrst time, you will need to insert the provided CR3032 battery.

1) Remove the battery cover using a coin. Turn in

the direction of the arrow.

2) Place the included battery (CR3032) in the

compartment. Note: e + symbol should be

facing up.

3) Replace the battery cover (the two dots will line

up). e Sensor Pad is now ON.

2.2  INSTALL THE SENSOR PAD ON THE MATTRESS SUPPORT

IMPORTANT

If your crib does not have a solid, stable surface for the Sensor Pad, you will need to place a

support under it, to ensure correct operation of the system.

is hardboard support should be at least 1/4’’ (6 mm) thick and should have minimum dimensions

of 13’’ x 13’’ (33 x 33 cm). is support board must be larger than the Sensor Pad surface area.

e Sensor Pad functions with any size and type of mattress except memory-foam mattresses,

hollow frame mattresses and water beds. e hardboard maintains a constant pressure on the

Sensor Pad, enabling it to detect the baby’s movements even when the baby is at the edges of the

crib.

Hardboard

Sensor Pad

1) Remove the mattress from the crib.

2) Place the Sensor Pad - Angelcare

logo

side

up - in the center of the mattress. It should be

centered on the hardboard if your crib requires

a hardboard support.

3) Replace the mattress.

WARNING -

• e Sensor Pad is not designed for use with adults, children or infants older than 24 months.

• Discontinue used of the Sensor Pad when child is older than 24 months. Remove Sensor Pad from crib

and store for future use.

• BEFORE FIRST TIME USE: To test that the unit is ready for use, refer to instruction manual on how to test

that the installation has been done correctly.

STEP 3  TURNING ON YOUR MONITOR

Press and hold the Nursery Unit

ON/OFF button for

2 seconds until the Nursery Unit

Indicator ﬂashes slowly in green.

e Nursery Unit will emit a sound and ﬂash blue to

conﬁrm pairing with the Sensor Pad

NOTE:

If the green light does not appear but the red

light is ﬂashing; or if there are false alarms,

adjust the sensitivity level (Step 4.3).

03m11_Manuel_AC017_NA_12643.indd 5 2018-01-29 2:02 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Angelcare AC017 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info