Bedienungsanleitung AOC ct710g crt monitor (Seite 3 von 7) (Englisch)

216455

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Plug & Play DDC1/2B Feature

This monitor is equipped with VESA DDC1/2B capabilities

according to the VESA DDC STANDARD. It allows the monitor to

inform the host system of its identity and, depending on the level

of DDC used, communicate additional information about its display

capabilities. The communication channel is defined in two levels,

DDC1 and DDC2B.

The DDC1 is a unidirectional data channel from the display to the

host that continuously transmits EDID information. The DDC2B is

a bidirectional data channel based on the I²C protocol. The host

can request EDID information over the DDC2B channel.

THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF

THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS

MONITOR TO OPERATE PROPERLY, THERE MUST BE A

VIDEO INPUT SIGNAL.

This monitor meets the Green Monitor standards as set by the

Video Electronics Standards Association (VESA) and/or the United

States Environmental Protection Agency (EPA) and The Swedish

Confederation Employees ( NUTEK ). This feature is designed to

conserve electrical energy by reducing power consumption when

there is no video input signal present. When there is no video input

signal this monitor, following a time-out period, will automatically

switch to an OFF mode. This reduces the monitor's internal power

supply consumption. After the video input signal is restored, full

power is restored and the display is automatically redrawn. The

appearance is similar to a "Screen Saver" feature except the

display is completely off. The display is restored by pressing a key

on the keyboard, or clicking the mouse.

USING THE RIGHT POWER CORD:

The accessory power cord for the Northern American region is the

wallet plug with NEMA 5-15 style and is UL listed and CSA

labeled. The voltage rating for the power cord shall be 125 volts

AC.

Supplied with units intended for connection to power outlet of

personal computer: Please use a cord set consisting of a minimum

No. 18 AWG, type SJT or SVT three conductors flexible cord. One

end terminates with a grounding type attachment plug, rated 10A,

250V, CEE-22 male configuration. The other end terminates with a

molded-on type connector body, rated 10A, 250V, having standard

CEE-22 female configuration.

TECHNICAL SUPPORT(FAQ)

Power LED is not on

*Power Cord should be connected

No Plug & Play

*Check if the PC System is Plug & Play compatible

*Check if the Video Card is Plug & Play compatible

*Check if the D-15 plug pin of Video Cable is bent

*Make sure the AOC Monitor Drivers are installed

(AOC Monitor Drivers are available at:

www.aocmonitor.com)

Picture is fuzzy

*Adjust the Contrast and Brightness Controls.

Picture bounces or a wave pattern is present in the

picture

*Move electrical devic

es that may cause electrical

interference.

The power LED is ON (orange) but there’s no video or

no picture.

*Computer Power Switch should be in the ON position.

*Computer Video Card should be snugly seated in its slot.

*Make sure monitor’s video cable is

properly connected to

the computer.

*Inspect monitor’s video cable and make sure none of the

pins are bent.

*Make sure computer is operational by hitting the CAPS

LOCK key on the keyboard while observing the CAPS

LOCK LED. The LED should either turn ON o

r OFF after

hitting the CAPS LOCK key.

Missing one of the primary colors (RED, GREEN, or

BLUE)

*Inspect the monitor’s video cable and make sure that none

of the pins are bent.

INSTALLATION INSTRUCTIONS

SWIVEL BASE

To attach the swivel base to the monitor, do the following:

 Carefully turn the monitor on its side or upside down.

(see figure 1)

 Locate the cavities at the bottom front of the monitor.

 Insert the pegs on the swivel base into these cavities. Push the

swivel base forward until the swivel base locks in place.

 To remove the swivel base, hold the bottom of the swivel base,

then push it out.

POWER CORD

Power Source:

1. Make sure the power cord is the correct type that required in

your area.

2. This monitor has a universal power supply that allows operation

in either 100/120V AC or 220/240V AC voltage area (No user

adjustment is required).

3. Connect the power cord into your monitor’s power input socket,

and then plug the other end into a 3-pin AC power outlet. The

power cord may be connected to either a wall power outlet or

the power outlet socket on your PC, depending on the type of

power cord supplied with your monitor.

VIDEO CABLE

Connecting the Video Cable: the monitor comes with a built-in

video cable. Plug the signal cables 15-pin connector into the

computer's video port and tighten the two screws on the cable

connector. (see figure 2)

Caution:Don’t bend the signal cable, otherwise it will break the

inner wire.

Connecting the Power Cord: Plug the power cord into the

monitor's AC power jack. Then plug the power cord into a

grounded AC outlet, UL-approved power strip, or the power

output socket on your PC.

Caution: If the AC outlet is not grounded, install the proper

grounding adapter (not supplied).

Connecting the Audio Cable ( CT740g only ): Plug audio cable

between the computer multi-media (or sound) card's audio output

and monitor's audio input.

Connecting the DC Power Cable ( CT740g only ): Plug DC

power cable between monitor to swivel base for audio power

AOC ct710g crt monitor Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info