Bedienungsanleitung Apart Concept 1 (Seite 3 von 6) (Englisch)

670185

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

CONCEPT1 RS232 COMMUNICATION

WWW.APART-AUDIO.COM

INFO@APART-AUDIO.COM

Operating Settings

MSCLVL is the music level. It can be OFF or a value between -79 and 0. If set at -80, it will be ”OFF”. If both

MULTIZONE and ZONELINK are ON, the corresponding zone needs to be specied.

MICLVL is the microphone level. It can be OFF or a value between -79 and 0. If set at -80, it will be ”OFF”. If

MULTIZONE is ON, the corresponding zone needs to be specied.

MAXMSCLVL is the maximum music level. If the music level is adjusted above the maximum, it will be changed to

the maximum value. In case both MULTIZONE and ZONELINK are ON, there sll are 2 dierent values possible for

zone 1 and zone 2. The dierence between those 2 levels will determine the oset between the volumes of both

zones. The maximum dierence in this mode is 40. Example:

SET MAXMSCLVL ZONE1 -16<CR>

SET MAXMSCLVL ZONE2 -10<CR>

Now, the volume can be adjusted between OFF and -10. The level in zone 1 will always be 6 dB lower than the level

in zone 2.

MAXMICLVL is the maximum microphone level. If the microphone level is adjusted above the maximum, it will be

changed to the maximum value.

SELECT is the source selecon. The source selecon in both zones is always the same, so it’s never needed to

specify the zone

Equalizer

Also the equalizer sengs are the same for both zones.

EQBASS sets the level of the bass.

EQTREB sets the level of the treble.

The value must be between -14 and 14 in steps of 2. If a dierent value is used, it will get changed to the closest

match.

Configuration Settings

AUTOLD is Auto Loudness and this is only acve in Stereo mode. It will adjust the equalizer depending of the

volume seng. If the auto loudness is on, the sound will sll be more “rich” at low levels.

PAGACT is paging acve. If set on, the microphone will only be on when there is a contact between pin A or B and

the ground of the connector at the backside of the amplier (see user manual). In that case, the music will be

muted as well. The Concept 1 will also send ”PAGING (ZONEx) ON/OFF<CR>” when the contacts are closed/opened

so the user can know the status.

IPGAIN is input gain. Each source input has its own gain seng so the source (A, B, C or D) needs to be specied.

The value can be between -20 and 14 in steps of 2. If an invalid value is used or no source is specied, “ERROR:

Value Invalid!<CR>” will be replied. Otherwise, the reply will be “Command Exicuted!<CR>”

ZONESPLIT is only used in MULTIZONE mode. Default, the zone split value is o, which means that le and right of

the sources will be mono summed in MULTIZONE mode. Some users would like to have a dierent music in each

zone by plugging dierent sources for le and right. By seng ZONESPLIT on, the le input will be sent to zone1

and right input to zone 2, like in stereo mode. This way, it’s possible to have dierent music in each zone but please

note that the source select will always impact both zones. The ZONESPLIT feature is implemented starng from

V1.0.2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Apart Concept 1 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Apart Concept 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info