578759
5
Zoom out
Zoom in
Vorherige Seite
1/14
Nächste Seite
A85/P85
5
English
Connecting to a power supply
Wrong plug?
Check that the plug supplied with the unit ts your supply and
that your mains supply voltage agrees with the voltage setting
(115V or 230V) indicated on the rear panel of the unit
2
before plugging in.
If your mains supply voltage or mains plug is different, consult
your Arcam dealer or Arcam Customer Support on +44
(0)1223 203203.
The product must be earthed.
Mains lead
The appliance is normally supplied with a moulded mains plug
already tted to the lead. If for any reason the plug needs to
be removed, it must be disposed of immediately and securely,
as it is a potential shock hazard when inserted into the mains
socket. Should you require a new mains lead, contact your
Arcam dealer.
Plugging in
Push the plug (IEC line socket) of the power cable supplied with
the unit into the socket (POWER INLET)
1
in the back of the
unit. Make sure it is pushed in rmly.
Put the plug on the other end of the cable into your power
supply socket and switch the socket on.
Standby power
For remote standby operation, the ampli ers control power
supply is kept powered up all the time the unit is connected to
the mains supply. The front panel power switch powers down
all other circuitry. Power consumption in this mode is less than
2W.
This means that even though the power switch is off, it may be
possible to hear a slight residual hum coming from the mains
transformer inside the ampli er. This is perfectly normal. If the
unit is to be left unused for an extended period, we recommend
that it is disconnected from the mains supply by switching it
off at the wall socket.
Connecting to other equipment
The use of high quality interconnect cables to and from your
ampli er is recommended to ensure the best sound quality.
Sockets marked
L (and R) on your ampli er should only be
connected to sockets marked L (and R) on other equipment. All
the line inputs have the same sensitivity and may be used with
equipment other than that labelled, if needed.
TAPE1/RECORD OUT
8
Connect these output sockets
to the input sockets of your cassette deck (usually labelled
RECORD).
TAPE1/PLAY IN
9
Connect these input sockets to the
output sockets of your cassette deck (usually labelled PLAY).
If you do not have a cassette deck you can use this input for
other (line level) equipment, such as a CD player, tuner, VCR,
etc., but not a turntable.
VCR/TAPE2 RECORD OUT
bk
These output sockets can
be connected to the input sockets of VCR/second recorder
(usually labelled RECORD).
VCR/TAPE2 PLAY IN
bl
Connect these input sockets
to the output sockets of your VCR/second recorder (usually
labelled PLAY). Alternatively, you can use this input for other
(line level) equipment such as a CD player, tuner, etc., but not
a turntable.
DVD
bm
Connect this input to the audio outputs of a DVD
player.
AV
bn
Connect this input to audiovisual equipment such as a
VCR, laserdisc player, satellite or Nicam tuner.
TUNER
bo
Connect this input to the audio outputs of your
radio tuner.
CD
bp
Connect this input to the audio outputs of your CD
player or DAC (digital to analogue converter).
AUX
bq
Connect this input to the audio outputs of any unit
with a line level output, e.g. tape deck, tuner etc.
NOTE: The AUX inputs must not be used if the phono module
is tted. When this is tted AUX becomes an output carrying
the equalised phono signal at line level.
PHONO
br
As standard, phono inputs are blanked. Phono
inputs are provided on a separate plug-in module which your
Arcam dealer or distributor can supply and t. This module
is compatible with most high output moving coil and moving
magnet cartridges (MM) and low output moving coil cartridges
(MC). MM or MC is selected via the MM/MC back panel switch.
Phono earth terminal For connecting your turntable earth
lead (if tted). Note that this terminal must not be used as a
safety earth.
TRIG OUT and REMOTE IN
3
(12V in and out) These
connections are for use in multi-room installations. In normal
use there is no need to make any connections to these
sockets. If you are bi-amping with a power ampli er and wish to
power both units on or off simultaneously, see page 11.
Pre/power ampli er connections
PWR IN
5
To use your integrated ampli er as a power
ampli er, connect the output of your pre-ampli er to the PWR IN
sockets.
Press in the
PRE/PWR switch
7
on the rear panel to
select separate pre-amp/power amp mode. Under these
circumstances your A85 has exactly the same speci cation and
performance as a power ampli er (see page 8).
PRE OUT
6
To use your integrated ampli er as a pre-
ampli er, connect the PRE OUT sockets to the input sockets
of your power ampli er. With a power ampli er of the correct
gain (e.g. the P85 power ampli er) you can bi-amplify (bi-amp)
suitable loudspeakers, giving signi cant improvements in sound
quality (see page 12).
A85/P85 multi.id 03/29/01, 3:34 PM5
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Arcam DiVA A85 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info