Bedienungsanleitung Arcam Neo (Seite 4 von 88) (Deutsch, Englisch, Holländisch, Französisch)

578807

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Interconnect cables

We recommend the use of high-quality screened

cables, since inferior-quality cables will degrade the

overall quality of your system. Use only cables that

are designed for the particular application as other

cables will have dierent impedance characteristics

that will degrade the performance of your system (for

example, do not use cabling intended for video use to

carry audio signals). All cables should be kept as short

as is practically possible.

It is good practice when connecting your equipment

to make sure that the mains power-supply cabling is

kept as far away as possible from your audio cables.

Failure to do so may result in unwanted noise in the

audio signals.

installation

guidelines

General guidelines

Positioning the unit

< Place Solo Neo on a level, rm surface, avoiding

direct sunlight and sources of heat or damp.

< Do not place Solo Neo on top of a power

amplier or other source of heat.

< Do not place Solo Neo in an enclosed space

such as a bookcase or closed cabinet unless

there is good provision for ventilation. Solo is

designed to run warm during normal operation.

< Do not place any other component or item on

top of Solo Neo as this may obstruct airow

around the heat-sink, causing Solo Neo to run

hot. (The unit placed on top of Solo Neo would

become hot, too.)

< Make sure the remote-control receiver

in the centre of the front panel display is

unobstructed, otherwise this will impair the

use of the remote-control. If line-of-sight is

impractical, a remote-control repeater can be

used with the rear panel connector (see page 5).

< Do not place your record deck on top of this

unit. Record decks are very sensitive to the noise

generated by mains power supplies which will

be heard as a background ‘hum’ if the record

deck is too close.

DIGITAL

OUT

AV IN

SERIAL NO .

GAME TVTAPE OUT iPodZONE 2 PRE OUT

230V

50 – 60HZ

400V A

MAX

PROGRAM

SPEAKER

OUTPUT

12V

REMOTE

INOUT IN

TRIGGER

LOCAL

ZONE 2

ETHE RNET

rDock / RS232

US B

DAB+

/FM

WiFi

Power

Solo Neo is supplied with a moulded mains plug already tted to the lead.

Check that the plug supplied ts your supply – should you require a new

mains lead, please contact your Arcam dealer.

Push the IEC (kettle-style) plug end of the power cable into the socket

on the back of Solo Neo, making sure that it is pushed in rmly. Put the

plug on the other end of the cable into your power supply socket and, if

necessary, switch the socket on.

Solo Neo is tted with a power switch on the rear of the product, next to

the power inlet. To use Solo Neo, make sure that this is switched on.

Solo Neo is tted with a transformer designed to accept the mains

voltage in the region that the product was shipped to. If your mains

supply voltage does not match this specication (as shown on the

rear panel), you wish to take the unit to a region with a dierent main

voltage, or the mains plug is incorrect, please consult your Arcam

dealer.

This product must be earthed.

Radio aerial and Wi- antenna

Solo Neo is tted with a combined FM/DAB (digital radio) receiver

module. In order to use the radio, you must connect an aerial to the unit –

a suitable aerial is supplied as an accessory.

The FM/DAB aerial connector is an F-type (screw) connector. The aerial

should be connected to this input by pushing the pin into the hole in the

centre of the connector, then screwing the sleeve onto the outside.

To use the supplied ‘T’ shaped wire aerial, mount it as high up as possible

on a wall with the elements positioned vertically. If accessable, try each

usable wall of the room to see which gives the best reception. Use tacks

or adhesive tape to secure the aerial to the wall, but ensure that tacks do

not come into contact with the internal wire of the aerial.

For optimal reception, the use of a roof-mounted (external) aerial is

recommended (see page 7).

A socket is provided for the supplied Wi- antenna. Fit this if you wish

to use Solo Neo with your wireless computer network for Internet radio

and network streaming functions. Note: equipment cabinets can block

wireless signals. Do not use a cabinet if you experience problems with

wireless reception.

Speakers

Solo Neo is designed to drive a single pair of speakers, rated between 4

and 8 ohms, and is tted with speaker terminals that can accept either

spade terminals or bare wires.

To connect the left speaker, unscrew the terminals on the back of Solo

Neo labelled L, insert the speaker wire (or spade) and screw the terminals

back up. Make sure that the red (positive/+) terminal of the speaker is

connected to the red terminal on Solo Neo and the black (negative/–)

terminal of the speaker is connected to the black terminal on Solo Neo.

Repeat the above to connect the right speaker to the terminals labelled R.

It is important that no stray strands of wire from these connections are

allowed to touch another cable or the product casing. Failure to ensure

this can cause a short circuit, and damage to your Solo Neo.

Do not over-tighten the loudspeaker terminals, or use a wrench, pliers,

etc., as this could cause damage to the terminals which will not be

covered under warranty.

See page 6 for tips on speaker positioning.

Arcam Neo Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info