Bedienungsanleitung Arcam solo movie 2 1 (Seite 5 von 30) (Englisch)

160350

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

E-5

movie 2.1

solo

English

front panel controls

Power

Note that the primary power-switch for Solo Movie

2.1 is on the rear of the unit. If the power light is not

illuminated at all, check that the unit is receiving mains

power and the rear power switch is ‘on’.

Press the

POWER button to switch Solo Movie 2.1

between ‘on’ and ‘stand-by’.

When Solo Movie 2.1 is in stand-by, the light next to

the power button on the front-panel glows red, and

the front-panel display shows the current time. Pressing

POWER when the unit is in stand-by will cause the unit to

switch on and the power button light turns blue.

You can also press and hold the

POWER button to put

the unit into ‘hard stand-by’ – a very low-power option

that retains clock settings (see page 21).

MENU SOURCE INFO OK

POWER

VOLUME

TAPE

�

�

In power stand-by mode, press

the MENU button to switch

between the clock and the

alarm display.

In power-on mode, press

MENU to access the Ampliﬁer

menu. Press and hold MENU to

access the Advanced Set-up

(On-Screen Display) menus.

Source –/+

Press the SOURCE+ or SOURCE–

button to cycle through the

available signal sources. If the

Ampliﬁer menu is active, these

buttons navigate through the

menu items (see page 15).

Info

Press the INFO button to

cycle through the available

information screens on the

front panel display for the

current source.

Press the OK button to conﬁrm

a selection (a DVD menu

choice, for example).

(Stop/Eject)

Press the

button once for a ‘resume

stop’; press again for a ‘complete stop’ . Once

stopped, pressing again ejects the disc.

Note that some DVDs do not allow you to

eject in all situations (e.g. while the disc is

displaying a copyright notice).

Headphone output

This 3.5mm stereo jack

socket is for connecting a

set of headphones. Sound to

the speakers is muted when

headphones are used.

Tape input

This is a stereo analogue input,

suitable for audio sources such

as a portable tape player, MP3

player or games console.

Play/Pause

Press the

;

button to start

playing a disc, pause a playing

disc, or resume playing a

paused disc.

Skip back/forward

To skip ‘chapters’ on a DVD (or

‘tracks’ on a CD), press

The buttons are also used to

step through option settings

when the Ampliﬁer menu is

active (see page 15).

When skipping back, the ﬁrst

button press takes you to

the beginning of the current

chapter. Pressing the button

again takes you to the start of

the previous chapter.

Mute

Use this button to mute the

volume. If Solo Movie 2.1 is

muted, pressing the MUTE

button for a second time

or changing the volume will

unmute it.

Volume –/+

Use these buttons to decrease

(–) or increase (+) the volume.

If Solo Movie 2.1 is muted,

changing the volume will

unmute it. The current volume

setting is shown on the front

panel display.

Front panel display

This is a vacuum ﬂuorescent

display with variable brightness.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam solo movie 2 1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam solo movie 2 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info