Bedienungsanleitung Argo Emix Tank (Seite 4 von 29) (Englisch)

665483

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

When connecting refrigerant tubing

• Keep all tubing runs as short as possible (max. 10m), accordingly to the allowable distances from the outdoor unit (see

manual).

• Use the flare method for connecting tubing.

• Apply refrigerant lubricant to the matching surfaces of the flare and union tubes before connecting them; screw by

hand and then tighten the nut with a torque wrench for a leak-free connection.

• Check carefully for leaks before starting the test run.

• Insulate the tubes with foamed polyethylene (min. thickness 8mm)

When connecting hydraulic tubing

• Keep all tubing runs as short as possible.

• Insulate the tubing.

• Check carefully for leaks before starting the test run.

When servicing

• Turn the power OFF at the main power board before opening the unit to check or repair electrical parts and wiring.

• Clean up the site after the work, remembering to check that no metal scraps or bits of wiring have been left inside the

unit being serviced.

• Ventilate the room during the installation or testing the refrigeration system; make sure that, after the installation, no

gas leaks are present, because this could produce toxic gas and dangerous if in contact with flames or heat-sources.

•

We recommend this appliance to be installed properly by qualified installation technicians in accordance with the installation

instructions provided with the unit.

• Do not install this appliance where there are fumes or flammable gases, or in an extremely humid space such as a green

house.

• Do not install the unit where excessively high heat-generating appliances are placed.

• Do not install the unit where it could be wetted by drops of water (i.e. in laundries).

• Do not install the unit in rooms with high humidity and subjected to high steam production (in the bathroom, for example).

• Do not install the unit outside.

• Do not install the unit in rooms exposed to the risk of freezing.

IMPORTANT ! The room in which the product is installed must be equipped with floor drain sump, connected to

sewer system.

AVOID

• Direct sunlight.

• Areas where leakage of flammable gas may be expected.

• Locations where large amounts of oil mist may occur (such as in kitchen or near factory equipment) because oil

contamination can cause operation problems.

• To make holes in areas where electrical wiring or conduits are located.

IMPORTANT !

In the absence of the precautions described above, THE MANUFACTURER shall not be held responsible for

any damage caused.

WARNING

INSTALLATION LOCATION

ELETRICAL REQUIREMENTS

• Before installation, check that the voltage of the electric supply in your home or office is the same as the voltage shown

on the nameplate.

•



All wiring must conform to the local electrical codes. Consult your dealer or a qualified electrician for details.

•

The unit must be properly grounded with a ground (or earth) wire or through the supply wiring.

•

Wiring must be done by a qualified electrician.

• Deoxidized annealed copper tube for refrigerant tubing connecting the units of the system, it has to be insulated with

foamed polyethylene (min. thickness 8mm). See paragraph “REFRIGERANT CIRCUIT” for dimensions.

• Anti-freeze oil for flare connections (about 30g.).

• Electric wire: use insulated copper wires of size and length as shown at paragraph “ELECTRICAL CONNECTIONS”.

• Tubes for water.

• If the water hardness exceeds the value of 20 ° F (1 ° F = 10mg of calcium carbonate per liter of water) the installation

of a polyphosphate treatment system responding to current regulations (DPR 59/09 UNI 8065) is required.

1. Also check the PH of water that should be at least neutral (values from 6.9 to 7). Values below 6.9 can cause corro-

sion of materials.

2. It is necessary to wash throughly the system after installation of the appliance and before its use.

ADDITIONAL MATERIAL REQUIRED FOR INSTALLATION (NOT SUPPLIED)

NOTES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Emix Tank Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Emix Tank

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info